Incon 1250B Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 36

Incon 1250B Скачать руководство пользователя страница 9

9

2.0 PROGRAMMING

The Model 1250B has three methods of programming, numeric menu, alphanumeric

menu, and serial port programming commands. Depending upon the serial port option
ordered, the serial programming commands will be either RS-232 ASCII commands or RS-
485 packet commands. (See Table 2.1 for a full listing of all programming menu items. See
Figure 2.1 for a simple programming flowchart. See Table 2.2 for a full listing of all serial
port programming commands and syntax.)

To access the numeric or alphanumeric programming menu, press the MENU key for

several seconds until the display goes blank, then press the SELECT/ENTER key. The
display should read “OP 0”. The default menu is the numeric menu. To choose the
alphanumeric menu, press the DOWN key to select OP 99. Press the SELECT/ENTER key,
the display should read “to OP”. Press the UP key. The display should read “run”. You are
now in the alphanumeric menu mode.

To change a parameter using the numeric or alphanumeric menus, select the parameter

to be changed from the menu, press the SELECT/ENTER key. The parameter’s present
setting will now be displayed. You can change the setting by pressing the UP or DOWN key.
To store the new setting, press the SELECT/ENTER key. The display will return to the
menu.

Table 2.1 Numeric and Alphanumeric Menu Items:

Num-
eric

Alpha-numeric
Protocol

Default
Value:

Programmable Range: Function:

OP 0

Run

Press the SELECT/ENTER key to exit the
Program mode

OP 1

rLY E

OFF

On or OFF

Enables the High/Low Relays

OP 2

Func

1

1, 2, 16, 17, 18, 19, 20, 21

Select Operating Mode (see page 12)

OP 3

CPt

360

-99999 to +99999

Scaled Mode: Counts per Turn

OP 4

LEFtd

4

0 to 5

Scaled Mode: Sets the number of digits to
the

left

of the decimal point

OP 5

An L

0.0000

-99999 to +99999

Scaled Mode: Analog output low limit

OP 6

An H

360.00

-99999 to +99999

Scaled Mode: Analog output high limit

OP 7

rLY L

0.0000

-99999 to +99999

Scaled Mode: Relay Low limit

OP 8

rLY H

8.0000

-99999 to +99999

Scaled Mode: Relay High limit

OP 12

tnS F

0.0000

0.0000 to +3600.0

Rotation Rate Filter Threshold

OP 13

FLttH

0.0000

0.0000 to +99999

Averaging Filter Threshold

OP 14

FdPth

0.0000

0 to 128.00

Averaging Filter Depth

OP 17 SEt P

0.0000

-99999 to +99999

Scaled Mode: Set preset position

OP 18 Ld P

Ld

Scaled Mode: Loads preset position into
memory

OP 19 CL P

CL

Scaled Mode: Clears position offset

OP 20 tAPS

33

2 to 100

Segmented Mode: Number of taps

OP 21

D SEG

10.000

-99999 to +99999

Segmented Mode: Degrees per tap

OP 22 NEu

1

0 to 9

Segmented Mode: Number of neutral taps

OP 23 N St

0-1

Any valid tap number

Segmented Mode: Sets neutral start tap

OP 24 rL Lt

-16

Any valid tap number

Segmented Mode: Sets low relay limit tap

«
...
7
8
9
10
11
...
»

Содержание 1250B





































Отзывы:

Нет отзывов