background image

1

Push down on the tabs on both sides and pull the 

cover up in the direction of the arrow shown in 

the picture.

Install the batteries, making sure to match the 

positive and negative ends of the batteries to 

the correct contacts.

Place the battery cover in the direction of the 

arrow shown in the picture. Push down on the 

tabs to get the cover click into its place.

2

3

Page 3

BATTERY INFORMATION

BATTERY INSTALLATION

The device is supplied with 4 AA Alkaline batteries.
The device can be used for approximately 9-17 hours based on the operating frequency 

chosen. Battery life will be less in 5kHz compared to other frequencies. Other factors such 

as LED flashlight usage and usage of speaker or wired/wireless headphones will also affect 

battery life.
AA Alkaline batteries are recommended for the best performance. Good quality Ni-MH 

rechargeable batteries can be used, instead. Rechargeable batteries with high mAh (capacity) 

ratings offer extended operating times versus batteries with lower rating. Do not mix alkaline 

and rechargeable batteries. 

Low Battery Level

Battery icon on the display shows the battery life status. When the charge decreases, the 

bars inside the battery icon decrease,  too. "Lo" message appears on the display when the 

batteries are depleted.

Содержание Nokta









































Отзывы: