manualshive.com logo in svg

impact AG 139, Руководство пользователя

Поделиться
Скачать
impact AG 139 Скачать руководство пользователя страница 21

 
 
 
 

 
Physical Data (Boxed) 

 
Width 70 

cms 

Depth 30 

cms 

Height 70 

cms 

Volume 0.15 

cu 

meters 

Weight 31 

Kg 

 
 

Standard Accessories 
 

Carrying Case - Sturdy case with dense foam inserts giving excellent protection. 
‘F’ Scale - Built in, for use with small slider set for 76mm-slide length. 
Set of 6 Sliders  - Certificate included. (Choice of large or small). 
125-127mm Setting Gauge - Used to set slide length for road / floor testing. 
Thermometer - For recording the air and surface temperature. 
Brush - For removing unwanted dirt or grit from the test area. 
‘C’ Spanner - For attaching and releasing the arm to the rotating head. 
17mm Spanner - For fitting rear foot. 
Allen Keys - for various adjustments. 
Water Spray Bottle - For wetting the test surface. 
Feet Pads - For placing under the levelling feet when on soft ground. 
Operating Instructions - A guide to road, floor and PSV testing. 
Calibration Certificate - Certifying the machine has been calibrated to BS EN 1097-
8:2000 (accredited under ISO 9003). 

 

BASE PLATE 

The base plate is used in conjunction with the skid tester and is used to hold the 
PSV samples in place.  

- 19 - 

Содержание AG 139





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды