IMO ACE3 Series Скачать руководство пользователя страница 20

Страница: 20 / 23

501

1020

Fig. 13

Fig. 14

Fig. 11

Fig. 12

Fig. 15

• Separate the front

cover 501 and the

power rotor 1020.

xTxx

• Place the front cover 501 on a pair of wood-

en pieces.

• Press out the shaft seal, stationary member

with a suitable tool.

• Loosen the shaft seal rotating member.

• Remove and inspect the

idler rotors 202.

202

• Remove the secondary seal 125 with a

suitable screw driver.

Fig. 16

xTxx

501

125

• Insert two suitable

screw drivers in

the carrier S5 slots

and gently push the

rotating member

S4, S7 off the rotor

shaft.

• Loosen the two

stop screws S8

(3 mm Allen key)

on the carrier S5

and pull it off.

xVxx

xTxx

xQxx

xVxx

Rotating

Member

Product Specification Sheet

X-Cel House, Chrysalis Way, Langley Bridge, Eastwood, Nottinghamshire NG16 3RY

Tel: +44 (0) 1773 302 660 | Email: [email protected] | Website: www.northridgepumps.com

Содержание ACE3 Series
























Результаты поиска

Содержание ACE3 Series

Отзывы:

Похожие инструкции для ACE3 Series

Бренды по названию

Популярные бренды

IMO ACE3 Series, Руководство по эксплуатации

Результаты поиска

Содержание ACE3 Series

Отзывы:

Похожие инструкции для ACE3 Series

Бренды по названию

Популярные бренды