manualshive.com logo in svg

ImmersionRC EzAntennaTracker, Руководство по эксплуатации

Поделиться
Скачать
ImmersionRC EzAntennaTracker Скачать руководство пользователя страница 5

 

5 

2.

 

Installation 

2.1.

 

Airborne Electronics 

Not much to do on this side, the EzOSD is equipped to transmit telemetry data down the right audio 
channel.  

Ensure that the cable running between the EzOSD and the transmitter is cabled correctly for video and 
stereo audio (for LawMate systems, take the right channel of the stereo pair from the EzOSD, and route 
that to the mono audio input of the Lawmate transmitter). 

2.2.

 

Ground Station Electronics 

The EzAntennaTracker -Lite module requires the following connections: 

1. Audio Input 

The audio input is supplied via a 4-Pole, 3.5mm jack, with the same pinout used for other Fat Shark, and 
ImmersionRC equipment.  

Only the AUDR (Audio, Right), and Ground pins are connected on this connector.  

2. Servo Power 

Power for the servos, and the EzAntennaTracker module itself,, must be supplied through a standard 3-
pin servo connector (with only two of the pins used).  

Looking at the front of the module, power must be provided through either of the lower two connectors 
(these are paralleled, and may be use to daisy-chain power to other devices).  

Power the EzAntennaTracker unit the same way you would power a R/C receiver. 5v or 6v depending 
upon servo requirements, sourced from either a ‘Rx Battery Pack’, or a 5v/6v BEC. 

3. Pan Servo 

The upper of the 4 connectors is the Pan Servo connection. Connect any R/C servo to this connector. See 
elsewhere in this document for servo recommendations.  

4. Tilt servo 

The connector below the Pan Servo connector is for the Tilt servo.  

 

Note that the USB connection is currently used primarily for upgrading flash firmware, and may be left 
disconnected in normal use. 

 

 

 

Содержание EzAntennaTracker





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды