background image

Technical documentation 

 

Technical documentation

 

STZS ed. 06/03

 

20

 

ZEUS SUPERIOR

 

 

 

LOW-VOLTAGE CIRCUIT 

SAFETY DEVICES AND CONTROLS 

 

Central-heating sensor 

(NR) 

Allows the modulation board to detect the temperature of the primary 
circuit water flow. 
If this sensor stops working, burner operation stops both in central-
heating and d.h.w. modes. 
It is positioned at the outlet of the main exchanger. 

Sensor NTC  

10 kohm 25 ºC 

 

 

 

Control zone unit (CZ) 

(external optional) 

Permits boiler operation with 3 area valves /external pumps controlled 
by respective room thermostats. 
Zone 1 is controlled 

(times/temperatures) 

by means of the CAR 

(if 

fitted).

 

See control unit 

zone operation 

 

 

 

Domestic hot water sensor 

(NB) 

This enables the modulation board to detect the temperature of the hot 
water in the storage tank. 
Its failure stops burner operation in domestic hot water phase. 
It is inserted inside a bulb holder in contact with the external wall of 
the cylinder. 

Sensor NTC  

10 kohm 25 ºC 

 

 

 

External sensor (NE) 

(external optional) 

Detects external temperature and enables the modulation board to 
change the system flow temperature according to outside temperature. 

Sensor PTC  

1 kohm  25 ºC 

 

 

 

Flue pressure switch 

(SV) 

This acts on the modulation board and enables burner operation when 
flue expulsion occurs correctly. 
If this is closed with the fan off, the ignition cycle will not start.

 

2-position switch

 

 

 

 

Pump pressure switch  

(SP) 

This acts on the modulation board and permits interrupting power to 
the control unit in the event of there being no circulation in the boiler 
circuit. 

Double-contact 

switch  

 

 

 

Remote control (CAR) 

(external optional) 

Permits remote control of boiler 

iSUM/WINT switch, temperature 

adjustment and indication, alarm display, reset, etc.)

 and acts as a 

weekly chrono-thermostat. 
Together with the external sensor (NE), allows the modulation board to 
change the system flow temperature according to need. 

See Remote 

Friend Control 

operation (CAR

 

 

 

Room thermostat (TA) 

(external optional) 

This enables operation in central heating phase when the room 
temperature is below that required. 
In case of CAR installation, the room thermostat must be disconnected 
without resetting the pre-existing jumper P1. 

Double clean-

contact switch 

 

 

 
 

LOADS 

 

Display board 

This displays burner operation 

(orange LED),

 operation in d.h.w. phase (

green LED)

 and in 

central-heating or antifreeze phase 

(green LED

) on the control panel. 

By means of a dispaly, it indicates the temperature of the boiler, the temperatures set for 
d.h.w. and central-heating and the error codes

 (see modulation board operation).

 

 

 

Modulation coil (MOD) 

This is powered by the modulation board with variable direct current. 
It permits changing gas pressure to the burner. 

 

 

Содержание ZEUS 21 Superior

































Отзывы: