IMG STAGE LINE PARL-20DMX, Инструкция по эксплуатации

Страница: 12 / 56

1. The wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E or with the
earth symbol , or coloured green or green
and yellow.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with
the letter N or coloured black.
3. The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
Warning – This appliance must be earthed.
3 Applications
The LED spotlight PARL-20DMX is used for effect
lighting, e. g. on small stages, in clubs or function
rooms. It uses 7 extra bright 8 W RGBW LEDs as a
light source for coloured light or white light. Various
operating modes are available (e. g. automatic or
music-controlled show programs, stroboscope
effects).
The spotlight is designed for operation via a
DMX light controller. The number of DMX control
channels is selectable: 1, 2, 5, 6 or 8. The spotlight
can also be operated without a controller, either on
its own or together with multiple PARL-20DMX
(master / slave mode).
4 Installation / Setting Up
G
To prevent heat accumulation inside the unit,
always position the spotlight in such a way to
ensure sufficient air circulation during operation.
Never cover the air vents of the housing.
G
The distance to the illuminated object should be
50 cm as a minimum.
Use one the mounting brackets (1) to install the
spotlight, e. g. with a stable mounting screw or a
support for lighting units (C hook) on a cross bar.
Alternatively, set up the spotlight on its own: Fold
out the mounting brackets underneath the spotlight
and use them as a stand.
To align the spotlight or to adjust the brackets,
release the two locking screws (2) of the brackets,
make the adjustment, then fasten the locking
screws again.
4.2 Barn doors
To reduce the beam angle, optional bar doors
PARL-20B are available. Slide the barn doors into
the outer rails at the front of the spotlight and use
the locking bracket (4) to secure them (
fig. 3). A
spring (arrow in fig. 3) will keep the bracket in place.
5 Setting the Spotlight into Operation
For operating the spotlight with a DMX controller or
for the master / slave mode, make the corresponding
control connections (
chapter 1, step 5). For con-
nection, special cables for DMX signal transmission
are recommended (e. g. cables of the CDMXN
series from IMG STAGELINE). For cable lengths
exceeding 150 m, it is recommended to insert a
DMX level matching amplifier (e. g. SR-103DMX
from IMG STAGELINE).
To switch on the spotlight, connect the plug of the
mains cable (6) to a socket (230 V~
/ 50 Hz). To
switch off, disconnect the mains plug from the
socket.
Caution: Never use a dimmer to connect the spot-
light to the mains voltage!
6 Operation
A menu is used to make the settings for the spot-
light. To operate the menu, refer to chapters 6.1
and 6.2.
Operation with a DMX controller
Select the channel mode (menu item ) and set
the DMX address (menu item ). If required, use
the menu to set additional functions (e. g. behaviour
of the spotlight after loss of control signal). The
spotlight will be set to operation via the DMX con-
troller when the menu item
is called up (indi-
WARNING To prevent damage to your eyes,
never look directly into the light
source for any length of time.
Please note that fast changes in light-
ing may trigger epileptic seizures with
photosensitive persons or persons
with epilepsy!
WARNING Install the spotlight safely and
expertly. When installing it at a place
where people may walk or sit under
it, additionally secure it [e. g. via a
safety rope attached to one of the
two rings (3) on the housing; fasten
the safety rope in such a way that the
maximum falling distance of the unit
will not exceed 20 cm].
If the spotlight is to be put out of operation
definitively, take it to a local recycling plant
for a disposal which is not harmful to the
environment.
12
English