IMG STAGE LINE LED-320RGBW "TRAPEZOID", Инструкция по эксплуатации

Страница: 9 / 26

For connection, special cables for high data flow
should be used. Standard microphone cables with
screening and a minimum cross section of 2 ×
0,22 mm
2 and with a capacity as low as possible
can only be recommended for a total cable length
of up to 100 m. For cable lengths exceeding 150 m
it is recommended to insert a DMX level matching
amplifier (e. g. SR-103DMX from “img Stage Line”).
1) Connect the DMX input (11) to the DMX output
of the light controller.
2) Connect the DMX output (12) to the DMX input
of the next light effect unit. Connect its output
again to the input of the following unit, etc. until
all light effect units are connected in a chain.
3) Terminate the DMX output of the last DMX unit
of the chain with a 120 Ω resistor (> 0.3 W): Con-
nect a corresponding terminating plug (e. g.
DLT-123 from “img Stage Line”) to the jack.
7.2 Adjusting the start address
For operating the unit with a light controller, adjust
the DMX start address for the first DMX channel. If
e. g. the address 5 on the controller is provided to
control the light effect unit, adjust the start address
5 on the LED-320RGBW. The DMX channels 2 and
3 are then automatically assigned to the two fol-
lowing addresses (in this example 6 and 7). As the
next possible start address for the following DMX-
controlled unit, the address 8 could be used in this
example.
Press the button MODE (6) so many times until the
display (4) shows the address last adjusted, e. g.
. Then adjust the address with the button UP
or DOWN (8).
After adjusting the start address, the light effect
unit can be operated via the DMX controller. Once
DMX signals are received, the point behind the let-
ter
in the display indication will flash.
8 Cleaning the Unit
The six lenses should be cleaned at regular inter-
vals, depending on impurities caused by dust,
smoke or other particles. Only this will ensure that
the light is radiated at maximum brightness.
For
cleaning, disconnect the mains plug from the
socket.
Only use a soft, clean cloth and a mild
detergent.
For cleaning the other parts of the housing, only
use a soft, clean cloth. Never use any fluid; it may
leak into the unit and cause damage.
9 Specifications
Power supply: . . . . . . . . . 230 V~/50 Hz
Power consumption: . . . . 30 VA
Illuminant: . . . . . . . . . . . . 156 super bright LEDs
(48 × red, 36 × green,
36 × blue, 36 × white)
Ambient temperature: . . . 0 – 40 °C
Dimensions, weight: . . . . 32 × 35 × 33 cm, 4.2 kg
9.1 DMX channels
Subject to technical modifications.
9
GB
All rights reserved by MONACOR ® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual
may be reproduced in any form or by any means for any commercial use.
Channel 1: Rotation
DMX
value
Function
0 – 100
rotation 0°
→
180°
101 no rotation
102 – 255
automatic rotation slow
→
fast
Channel 2: Pattern /chase (running light effect)
DMX
value
Function DMX
value
Function
0 – 7 LEDs off (blackout) 128 – 135 chase 1
8 – 15 pattern 1 136 – 143 chase 2
16 – 23 pattern 2 144 – 151 chase 3
24 – 31 pattern 3 152 – 159 chase 4
32 – 39 pattern 4 160 – 167 chase 5
40 – 47 pattern 5 168 – 175 chase 6
48 – 55 pattern 6 176 – 183 chase 7
56 – 63 pattern 7 184 – 191 chase 8
64 – 71 pattern 8 192 – 199 chase 9
72 – 79 pattern 9 200 – 207 chase 10
80 – 87 pattern 10 208 – 215 chase 11
88 – 95 pattern 11 216 – 223 chase 12
96 – 103 pattern 12 224 – 231 chase 13
104 – 111 pattern 13 232 – 239 chase 14
112 – 119 pattern 14 240 – 247 chase 15
120 – 127 pattern 15 248 – 255 chase 16
Channel 3: Stroboscope effect /chase speed
DMX
value
Function
(depending on the adjustment of channel 2)
0 – 7
8 – 255
if a pattern has been adjusted for channel 2
no stroboscope effect
stroboscope effect slow
→
fast
0 – 255
if a chase programme has been adjusted for channel 2:
chase speed slow
→
fast