Imetec GK5 100, Руководство по эксплуатации

Страница: 9 / 48

7
DESCRIPTION OF APPLIANCE AND ACCESSORIES
Refer to page I of the Illustrative Guide to check the contents of the package.
All the figures are found on the inside pages of the cover.
1. Connector to charge or use the device connected
to the mains
2. Charging LED
3. Data plate
4. button
5. Blade locking device
6. U-Blade
7. Button to adjust cutting length
8. Nose trimmer
9. Lubricating oil
10. Brush for cleaning
11. Spacer comb U-blade 1,5 mm
12. Spacer comb U-blade 3 mm
13. Spacer comb U-blade 6,5 mm
14. AC/DC adaptor with power cable
For the appliance features, refer to the external packaging.
Use only the supplied accessories.
CHARGING THE APPLIANCE
Before charging the appliance, insert the battery on the product as shown in .
Charge the appliance for 12 hours before using it for the first time and subsequently for 10 hours. A red
charge LED (2) appears while charging. The autonomy of a fully charged appliance lasts about 60 minutes.
Always make sure the appliance is completely dry before using and charging it.
• Switch the appliance on by pressing the button (4).
• Insert the adaptor (14) into an electrical socket.
• Connect the charging cable (14) to the connector (1) at the base of the hair trimmer.
Do not keep the appliance always connected to the socket.
Always switch off and unplug the hair trimmer after use and after charging.
To preserve the battery life of the hair trimmer:
• Do not charge every day. It is recommend to discharge the battery completely every six months and then
charge it for 12 hours.
• Do not exceed the recommended charging time. Excessive charging will reduce the durability of the
rechargeable batteries.
• If you do not intend to use the product for a long period of time, recharge it for 12 hours before putting it away.
OPERATING INSTRUCTIONS
ATTENTION! Never use the appliance if the blades are damaged or the blade locking
device does not work properly.
Warning: never use the appliance on wet hair.
Make sure the hair is dry and clean, with no trace of hairspray, hair mousse or gel. Then brush the hair in the
direction of growth to remove all knots.
ATTENTION! Switch the appliance off before changing any accessories.
USING SPACER COMBS (11-12-13)
Spacer comb Setting number Length obtained
None 1 0,5 mm
None 2 1,0 mm
None 3 1,5 mm
11 1 2,0 mm
11 2 2,5 mm
11 3 3,0 mm
12 1 3,5 mm
12 2 4,0 mm
12 3 4,5 mm
13 1 7,0 mm
13 2 7,5 mm
13 3 8,0 mm
Follow these instructions to insert a spacer comb:
• Choose the desired spacer comb, apply it on the product and select the length from the adjustment button (7).
• Ensure that the spacer comb is inserted properly into the grooves on both sides (5).
• With the spacer comb attached, the appliance has 21 different hair length settings and an additional 3
settings without any accessories.
• Adjust the spacer comb to the desired length by pressing the adjustment button (7) and sliding it to the
desired length setting.
• Switch the appliance on by pressing the button (4). Always switch the appliance off when not in use.
USEFUL RECOMMENDATIONS
• Start with the highest setting of the spacer comb and gradually decrease it until you have the desired hair length.
• For optimal results, use the device with the blades facing the opposite direction of hair growth.
• Move the appliance in different directions (upwards, downwards and sideways) because not all hair
grows in the same direction.
• If a lot of hair has accumulated in the spacer comb, remove the comb from the appliance and blow and/
EN