background image

8.

Press a 25mm Bushing (48) into each end of the
Locking Bar (34).

Insert the Barbell (35) through the Locking Bar (34)
until the Barbell is centered in the Locking Bar.

35

48

34

48

8

9.

Identify the Left Weight Glider (32) by looking at the
position of the round tube.

Press a 38mm Bushing (29) into each end of the
round tube on the Left Weight Glider (32). 

Slide the Left Weight Glider (32) onto the left end of
the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Screw (50).

Look at the drawing on page 4 to make sure that
you have correctly identified the left end. The Left
Weight Glider must be turned as shown in the
drawing.

50

32

29

35

Round tube

29

9

10. Identify the Right Weight Glider (31) by looking at the

position of the round tube.

Press a 38mm Bushing (29) into each end of the
welded tube on the Right Weight Glider (31). 

Slide the Right Weight Glider (31) onto the right end
of the Barbell (35). Secure the Weight Glider to the
Barbell with a hand-tightened M8 x 20mm Screw (50).

Make sure that the Weight Glider is turned as
shown in the drawing.

35

29

31

29

50

10

Round

tube

11. Identify the Left Safety Spotter (24) by the position of

the handle and the Left Spotter Hook (65). Place the
Left Safety Spotter on the left Base (7) so it is cen-
tered over the indicated hole.

Have a second person hold the Locking Bar (34) so
that the Left Weight Glider (32) rests on top of the
Left Safety Spotter (24). Insert a Weight Guide (18)
into the Left Weight Glider, the Left Safety Spotter,
and the hole in the Base (7). 

Note: Tilt the Weight

Guide away from the Upright (1) as you insert it.

Attach the Weight Guide (18) to the Base (7) with an
M8 x 60mm Bolt (39), two M8 Washers (52), and an
M8 Nylon Locknut (54). 

Do not tighten the Nylon

Locknut yet.

9

1

32

34

24

65

54

52

39

7

Hole

Handle

18

11

Содержание 4.8 Limited Edition Bench



















Отзывы: