background image

13

23. Place the Seat Support Tube (37) on the Bench

Frame (5) so that the Seat Adjustment Bracket (45)
fits over the welded pin (not visible in the drawing) on
the side of the Bench Frame. 

Lubricate an M10 x 80mm Bolt (56). Attach the Seat
Support Tube (37) to the indicated bracket on the
Bench Frame (5) with the Bolt and an M10 Nylon
Locknut (11). 

Note: Do not over tighten the Nylon

Locknut; the Seat Support Tube must pivot easily.

23

5

11

45

37

56

24. Turn the Seat (14) as shown. Attach the wide end of

the Seat to the bracket on the Seat Support Tube
(37) with two M6 x 16mm Screws (3).

Tilt the Seat Support Tube (37) upwards and attach
the narrow end of the Seat (14) to the Seat Support
Tube with an M6 x 38mm Bolt (60) and an M6
Washer (30).

24

60

30

3

37  

14

25. Attach the Curl Pad (13) to the bracket on the Front

Leg (19) with two M6 x 16mm Screws (3). 

25

3

19

13

26.

Make sure all parts are properly tightened before you use the weight bench. 

The use of all remaining

parts will be explained in ADJUSTING THE WEIGHT BENCH starting on the following page.

Welded

Pin

Lubricate

Содержание 4.8 Limited Edition Bench



















Отзывы: