Ikra RT 2008 DV GT 5530 Gardol, Руководство по эксплуатации

Страница: 16 / 88

GB-4
• Ideal working conditions are achieved if the trimmer is
tilted to the left at an angle approx. of 30°.
10. Adjusting nylon line
Check the nylon line regularly if it is damaged or if it still
has the correct length.
Your lawn trimmer is equipped with a fully automatic
thread adjustment function. This means, that, in case of
normal use, the worn thread will be automatically pro-
longed through a mechanism based on the centri-fugal
force. Thus, the user does not have to adjust the thread
length by hand any longer. Nevertheless, it is recom-
mended that you regularly check the nylon thread for
damages before you use the trimmer.
The thread is fully used up, if you realise a material
decrease of the cutting performance and a significant
higher speed. In this case, you will have to proceed as
described under point 11 (Replacing the thread coil).
Your trimmer has a thread cutting blade that continuously
cuts the thread down to the appropriate length (fig. 10).
Note: Clean the thread cutting blade from grass re-
mainders in order to guarantee an unaffected cutting
performance.
Attention: Danger of injury through the cutting blade !
11. Replacement of spool
(Fig. 11 + 12)
First, switch off and unplug the device. Wait until the ny-
lon thread has come to a halt. Then push the two locking
devices 1 at the sides of the cutting head, and remove
the cutting head cover 2. Remove the used thread coil
and put in the new coil 3 such, that one end of the thread
comes out of each outlet at the sides of the cutting head.
Finally, close the cover by pushing it in its seat. Both
locks must properly engage.
Optionally:
12. Twincut system
(Fig. 13 - 16)
This system has been designed to cut stronger vegeta-
tion as nettles, thistles and the like. But please bear in
mind that the TwinCut cutting system must never be used
to cut off brushwood, hedges, branches or similar.
Mounting the Twincut system (Fig. 13): To do this push
both locks 1 located laterally at the cutting head and
remove cover 2. Remove the coil 3 from the cutting head
housing. Store the cover and coil for future use.
The Twincut system is then put on the cutting head hous-
ing in the same manner as the coil cover. The two locks
of the Twincut system must be inserted exactly into the
corresponding reliefs in the housing. Please make sure
that both locks engage properly.
Dismounting the TwinCut system (Fig. 14): Push both
lateral locking buttons (1) and pull the TwinCut system off
in upward direction.
Mounting the cutters (Fig. 15): Put on cutters (1) and
push into final location until they lock into place (2).
Please take care that the cutters lock into place correctly.
Only in their correct position, the cutters can swing freely
(3). This is essential for safe operation. The device may
only be operated with two cutters mounted.
To replace the plastic cutters please proceed as follows
(Fig. 16):
Dismounting the cutters : Turn the cutters anticlockwise
as far as they will go (1). Then push in direction of arrow
pressing them down powerfully until they unlock (2);
remove cutters (3).
To insert the new cutters please proceed as described in
the paragraph ‘Mounting the cutters’.
Attention: If one or both plastic cutters are damaged or
worn out always replace them in pairs; otherwise, dan-
gerous balance errors may occur.
Switch the device off immediately if you detect unusual
vibrations or balance errors and check the condition of
both plastic cutters and the Twincut system. In case of
defects, defective parts must be replaced first.
13. Trouble shooting
• Trimmer does not work: Check power supply (e.g.
by testing on another socket or by means of a voltage
tester). Should it still not work, although the socket is
o.k., send it undismantled to an authorised service sta-
tion for repair.
• Cutting line disappears into spool: Remove spool
(acc. to point 11), pull end of line through the metal
outlet and reinsert spool. In case nylon line is used up
insert a new spool with line.
Do not make any other repairs on your own; have your
trimmer checked and repaired by an authorised dealer.
14. Storing
• Clean the unit thoroughly, especially the cooling air
slots on the motor housing.
• Do not use water to clean the device.
• Store trimmer indoors in a dry, high or locked place and
keep out of reach of children.
15. Guarantee
In the case of a claim for guarantee or defects, please
contact the place of purchase.
16. Waste disposal and environmental protec-
tion
If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose
of the device together with your domestic refuse, but dis-
pose of it in an environmentally friendly manner.
Please dispose of the device itself at an according col-
lecting/recycling point. By doing so, plastic and metal
parts can be separated and recycled. Information con-
cerning the disposal of materials and devices are avail-
able from your local administration.