Ikra ELM 1434 U, Руководство по эксплуатации

Страница: 22 / 96

5
GB | Operating Instructions
Assembly
This manual gives instructions on the correct assembly
and safe use of your machine.It is important that you read
these instructions carefully .When fully assembled the
machine weighs approximately 10kg. If necessary, obtain
assistance to remove from packaging, Take care when
carrying the mower to the lawn , as the blades are sharp.
Delivered Items
Carefully remove the machine from its packaging and
check that you have all the following items:
Lawnmower with handle assembly
• 2 Handles bottom
• 2 Bolts
• 2 Knob module (Thumb screw)
• 2 Screws
• Grass box
• Grass box cover
• Tongue
• 2 Cable clips
If bolts parts are missing or damaged, please contact
the consumer care hotline for assistance.
Assembly of switch box
(fig. 1 - 5)
1. Before using the lawn mower, you need to assemble
the switch box on handle lever as show in photo 5.
2. Align the groove of switch box to the guide rail, slide
the switch box toward the rear handle. (fig. 2 + 4)
3. Only with clips on switch box (fig. 3) located in posi -
tion to lock the switch box on handle lever as well as
the assembly indication line (fig. 4) aligned, then the
switch box assembled .
4. After fixing, move the switch box in reverse direction
to check if the switch box assembled in position or
not.
Assembly (fig. A)
Important! Before you assemble the lawn mo-
wer, check the accessories according above
information, make sure the accessories are
completed.
1. Insert the lower handles 6 into the holes provided in
the deck, secure with the screws (A1).
2. Attach the cable strain relief 4 to the upper handle
3 (A2).
3. Attach the upper handle 3 with bolts and knob module
5 to the lower handles 6 (A3).
4. The upper handle 3 is height adjustable. Handles can
be fixed in desired position I or II (A3).
Note: Ensure that the cable clips 12 are used to fix the
cable to the handle
Attach cable to cable strain relief
4 ensuring that sufficient
cable slack is available. (not for GB models)
Ensure cables are not trapped when folding/unfolding top
handles. Do not drop the handles.
Assembly of Grass box (fig. B)
1. Assemble the grip onto the upper cover of the catcher
(B1)
2. Slide the grass box tongue into the slots in the grass
box lower until it clicks securely into position. (B2)
3. Starting at the rear of the grass box, locate the grass
box cover into the grass box by sligning the clips. En-
sure all clips are correctly located. (B3 + B4)
4. Fitting assembled grass box to lawn mower (B5):
a) Lift the safety guard 8 (B5-a).
b) Make sure the discharge chute is clean and free
from debris.
c) Locate fully assembled grass box 7 onto location
points at the rear of the deck as illustrated (B5-b).
d) Locate safety flap onto the top of the grass box.
Ensure the grass box is easy located.
Note: For non grass collection the mower can be used
without the grass box in position, with the safety guard 8
in the down position.
Adjusting the Cutting Height
(fig. C)
Warning: release switch lever 1 and wait until the
motor stops before adjusting height. The blades
continue to rotate for a few seconds after the ma-
chine is switched off, a rotating blade can cause
injury.
Height of cut is adjusted by raising or lowering the Front
and Rear wheels. (C1&C2)
Confirm lock and simultaneously set the required height
by either pulling or pressing on the lever 13. When relea-
sing the lock, the setting selected snaps into place.
There are five heights of cut on this product.
NOTE
A medium height of cut is recommended for most lawns.
The quality of your mowing will suffer and collection will
be poor if you cut too low.
HEIGHT OF CUT WHEELS POSITION
Low 25 mm
Low to Medium 35 mm
Medium 45 mm
Medium to High 55 mm
High 65 mm
Starting and Stopping
(fig. D)
Make sure the blade stopped rotating before
switching “on” again.
Do not rapidly switch on and off.
Start:
• Press and hold the safety button 2. Squeeze the
switch lever 1 towards the handle (D).
• Release the safety button 2.
Stopp:
• Release the switch lever 1.