10
LLuubbrriiccaannttss
1. Ikelite provides silicone lubricant with the housing. We
recommend that you use only Ikelite lubricantas some other
brands may cause the o’ring to swell and not seal properly.
2. Use only enough lubricant to lightly cover control shafts and
o’rings. Wipe off any excess lubricant with a clean cloth.
Lubricant is not a sealant, it is used to reduce friction. Excessive
lubricant can collect sand and dirt which may interfere with
proper sealing.
CCAAU
UTTIIO
ON
N
N
Neevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
O
Oppttiioonnaall AAcccceessssoorriieess ccoonntt..
BBaacckk O
O’’rriinngg
##00111100
O’rings last for several years if properly maintained. (See
maintenance) Always carry a spare.
D
Duuaall H
Haannddllee TTrraayy
##99552233..1122
A Dual Handle Tray is available. The Dual Handle Tray provides
a second access point for mounting a second strobe.
9
O
Oppttiioonnaall AAcccceessssoorriieess ccoonntt..
D
DSS5511 SSuubbssttrroobbee
The Substrobe DS51 covers
the equivalent of a 28mm
lens. It is the ideal choice
when using only the camera
lens or the camera lens with a
macro accessory lens.
D
DSS112255 SSuubbssttrroobbee
The Substrobe DS125 covers
the equivalent of an 18mm
lens, 100 degrees (with
diffuser). It is the ideal choice
when using accessory wide
angle lenses greater than
28mm.
O
Oppttiioonnaall SSttrroobbee PPaacckkaaggeess
#3944.51 includes
DS51 Substrobe
Ikelite TTL Sync Cord
SA-100R Arm
#3944.75 includes
DS125 Substrobe
1.5 hr. Smart Charger
Ikelite TTL Sync Cord
SA-100R Arm
DS125
Substrobe
SA-100R
Arm
TTL Sync
Cord
11
M
Maaiinntteennaannccee
The Ikelite Digital Housing should be given the same care and
attention as your other photographic equipment. In addition to
normal maintenance we recommend that the housing be returned
to Ikelite periodically to be checked and pressure tested.
1. D
Doo N
Noott leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
2. D
Doo N
Noott ship the camera in the housing.
3. Before using the housing, always check the tightness of the sseett
ssccrreew
w in each control knob.
Check each ccoonnttrrooll ggllaanndd penetrating the housing to make sure
they are tight. There is a slight chance that either could vibrate
loose during travel.
4. Keep the back o’ring clean and lightly lubricated. To lubricate
remove the o’ring from the back. Put a small amount of lkelite
lubricant on your fingers. Draw the o’ring through your fingers
to apply a light coating of lubricant. Only apply enough
lubricant to make the o’ring feel slick. D
Doo N
Noott ssttrreettcchh tthhee oo’’rriinngg.
This light coating of lubricant will help to keep the o’ring from
drying out and will help to show a dark sealing line when the
housing back is properly sealed.
5. Keep the area where the o’ring fits and the sealing surface of
the housing clean.
6. Rinse the housing exterior thoroughly in fresh water after each
salt water use. Dry with a soft cloth. Dry lens port to eliminate
water spotting.
After several uses in salt water soak the housing in a mild soap
solution, rinse and dry before storage. When storing the
housing, remove the back o’ring, lightly lubricate and place in a
plastic bag. Place the plastic bag with o’ring inside the housing
for safe keeping.
CCAAU
UTTIIO
ON
N
N
Neevveerr uussee sspprraayy lluubbrriiccaannttss aass tthhee pprrooppeellllaanntt iinnggrreeddiieenntt ccaann
ccaauussee tthhee ppllaassttiicc hhoouussiinngg ttoo ccrraacckk..
