IIkkeelliittee LLiim
miitteedd W
Waarrrraannttyy
All Ikelite products are warranted against any manufacturing
defects for a period of one (1) year from the date of purchase.
Defective products should be returned prepaid to Ikelite. Ikelite
will, at its discretion, repair or replace such products, and will
return to customer prepaid. All other claims, of any nature,
including but not limited to bulb failure are not covered. Except as
mentioned above, no other warranty expressed or implied, applies
to this Ikelite product.
RReettuurrnniinngg PPrroodduuccttss ffoorr SSeerrvviiccee
Ikelite is most interested in preforming any service to assure
that all products perform as intended. For repair or service, return
the product to the address below with your name, address, phone
number and a brief description of the problem. Evidence of
purchase date must be provided to obtain warranty service.
IIkkeelliittee U
Unnddeerrw
waatteerr SSyysstteem
mss
5500 W
W 3333rrdd SSttrreeeett
IInnddiiaannaappoolliiss,, IIN
N 4466220088 U
USSAA
331177--992233--44552233
eem
maaiill:: iikkeelliittee@
@iikkeelliittee..ccoom
m
w
ww
ww
w..iikkeelliittee..ccoom
m
D
Diiggiittaall 6688 4411--0011--00220077
23
PPhhoottoo TTiippss
1. The number one rule in underwater photography is eliminate
as much water between camera and subject as possible. Get as
close as you can to the subject, then use the zoom. If you are
using flash, subjects beyond 6 feet (1.8m)will not have much
color.
2. Digital cameras have a slight lag time between when you press
the shutter release button and the camera actually takes the
picture. It only takes a slight amount of pressure to trip the
shutter, if the shutter doesn’t trip immediately don’t push down
harder on the shutter control as you may damage the camera.
Hold the camera steady a second or two after pressing the
shutter release button.
3. Do not shoot down on subjects as they will quite often blend
into the background and be difficult to see in the photograph.
Shoot subjects straight on or shoot up at a slight angle using
the blue water as a contrasting background.
4. Underwater flash is used to restore the warmer colors filtered
out by the water as well as to illuminate the subject.
5. For balanced lighting meter the background and set the camera
aperture accordingly. Use TTL, adjust the strobe’s power
settings, or move the strobe closer or farther away to properly
expose the subject with the chosen camera aperture.
22
GGeenneerraall TTiippss
1. You should completely assemble and test your set-up in a
swimming pool before using it in openwater.
2. It is a good idea to start each photo dive with a fully charged
battery(s) in the camera and strobes.
3. Before entering the water and as soon as you enter the water,
take a moment and check the housing to see that it is properly
sealed.
4. Next, check to see if there are any bubbles on the face of the
port. If there are, take your finger and remove them. If there
are bubbles on the lens port they can produce soft focus spots
in your photographs.
5. Set Image Resolution to the Highest JPG format available or
RAW. Higher resolution setting are required for printing. High
resolution images can easily be reduced in size with software
and retain their original quality. A Low resolution image can be
enlarged with software but much of the quality will be lost.
6. Digital images are usually transferred to the computer where
their appearance can be fine tuned. Many of the image
manipulation programs make you think you can magically
correct any image taken and make a good picture. One thing to
be aware of is that if an image is overexposed that some of the
color information in the file is missing. If the color is missing
you cannot adjust it. If images are underexposed the color and
detail may be there, it is just dark, and you can adjust it to some
degree. So if you error in exposure it is better to have the image
slightly underexposed than overexposed.
21
3. Some of the controls have a short shaft and cannot be pulled
out exposing the shaft for lubrication. In the unlikely event one
of these controls sticks or becomes difficult to operate you can
remove the control from the housing and lubricate it, or return
the housing to Ikelite for maintenance. To remove the control,
loosen the set screw in the knob (allen wrench required);
remove the knob. If there is salt or dirt build-up on the exposed
control shaft, clean the shaft. Open the housing and gently slide
the control shaft out of the control gland. Clean and lightly
lubricate the shaft, including the end of the shaft. Slide the
shaft back into the control gland and gently slide it back and
forth a few times without fully removing the shaft from the
gland. Replace the knob, NOTE the flat area on the shaft, the
set screw in the knob should tighten down against the flat
area on the control so the knob does not turn on the shaft.
Loosen set screw
(allen wrench required)
Flat
Tighten set screw down
against this area when
replacing the knob.
housing
gland
control
shaft
Lubricate end of shaft
before reinserting into
gland
