ENGLISH 7
in accordance with current
installation regulations. Particular
attention shall be given to the
relevant requirements regarding
ventilation.
IIf the appliances is connected
to liquid gas, the regulation screw
must be fastened as tightly as
possible.
IMPORTANT:
When gas
cylinder is adopted, the gas
cylinder or gas container must
be properly settled (vertical
orientation).
WARNING!:
This operation
must be performed by a qualified
technician.
Use only flexible or rigid metal
hose for gas connection.
Connection with a rigid pipe
(copper or steel) Connection to
the gas system must be carried
out in such a way as not to
place any strain of any kind
on the appliance. There is an
adjustable L-shaped pipe fitting
on the appliance supply ramp
and this is fitted with a seal in
order to prevent leaks. The seal
must always be replaced after
rotating the pipe fitting (the seal
is provided with the appliance).
The gas supply pipe fitting is a
threaded 1/2 gas cylindrical male
attachment.
Connecting a flexible jointless
stainless steel pipe to a threaded
attachment The gas supply pipe
fitting is a threaded 1/2 gas
cylindrical male attachment.
These pipes must be installed so
that they are never longer than
2000 mm when fully extended.
Once connection has been
carried out, make sure that the
flexible metal pipe does not
touch any moving parts and is
not compressed. Only use pipes
and seals that comply with current
National regulations.
IMPORTANT:
If a stainless steel
hose is used, it must be installed
so as not touch any mobile part of
the furniture (e.g. drawer). It must
pass through an area where there
are no obstructions and where it
is possible to inspect it on all its
length.
The appliance should be
connected to the main gas supply
or to gas cylinder in compliance
with the current National
regulations. Before carry out the
connection, make sure that the
appliance is compatible with the
gas supply you wish to use. If this is
not the case, follow the instructions
indicated in the paragraph
“Adapting to different types of
gas”.
After connection to the gas
supply, check for leaks with soapy
water. Light up the burners and
turn the knobs from max position
1* to minimum position 2* to check
flame stability.
Содержание ELDSLAGA
