IKA HB ECO Скачать руководство пользователя

Страница: 20 / 24

E21

Causes

› Safety relay does not open

Effect

› Heating switched off

Solutions

› Switch off the device and switch on again

E24

Causes

› Set safety temperature exceeded

Effect

› Heating switched off

Solutions

›  Switch off the device
›  Let the device cool down
›   Switch on the device

E25

Causes

› The heater control circuit switch (TRIAC) is faulty�
› The heater or the supply line is disconnected�

Effect

› Heating switched off

Solutions

› Switch off the device and switch on again

E26

Causes

› Dry running

Effect

› Heating switched off

Solutions

›  Switch off the device
›  Let the device cool down
›  Fill up the tempering medium
›  Switch on the device

Error code | Causes | Effect | Solutions

E 3

Causes

› Temperature inside the device is too high

Effect

› Heating switched off

Solutions

›  Switch off the device
›  Let the device cool down
›  Switch on the device

E 9

Causes

› Fault in storing the safety circuit set temperatures
› Memory chip (EPROM) defective

Effect

› Heating switched off

Solutions

›  Switch off the device
›  Let the device cool down
›   Switch on the device

Error codes

�

The fault is shown by an error code on the display as following if the error occurs�

Proceed as follows in such cases:

›  Turn off the device by using the main switch�
›  Carry out corrective measures�
›  Restart the device�

Содержание HB ECO

























Результаты поиска

Содержание HB ECO

Отзывы:

Похожие инструкции для HB ECO

Бренды по названию

Популярные бренды

IKA HB ECO, Инструкция по эксплуатации

Результаты поиска

Содержание HB ECO

Отзывы:

Похожие инструкции для HB ECO

Бренды по названию

Популярные бренды