15
Page
15
15
16
16
17
EU
Declaration of conformity
Safety instructions
Unpack
Correct use
Commissioning
HB 10 basic
Operating elements
Adjustable safety circuit
HB 10 digital/control
Heating
Operating modes
Safety circuit
Control of medium temperature
Interface
Assembly of spray guard and cover accessories
21
Error message
HB 10 basic
22
Error message
HB 10 digital/control
23
Maintenance and cleaning
24
Accessories
24
Warranty
24
Technical Data
25
We declare under our sole responsibility that this product corresponds
to the directives 2014/35/EU, 2014/30/EU and 2011/65/EU and
conforms with the following standards or normative documents: EN
61010-1, EN 61010-2-010, EN 61010-2-051, EN 61326-1, EN 60529
(A1+A2) and EN ISO 12100.
A copy of the complete EU Declaration of Conformity can be requested
at [email protected].
For your protection
• Read the operating instructions in full before starting up and
follow the safety instructions.
•
Keep the operating instructions in a place where they can be
accessed by everyone.
•
Ensure that only trained staff work with the appliance.
•
Follow the safety instructions, guidelines, occupational health
and safety and accident prevention regulations.
•
Wear your personal protective equipment in accordance with the
hazard category of the medium to be processed. Otherwise
there is a risk of splashing liquids.
•
Set up the device in a spacious area on an even, stable, clean,
non-slip, dry and fireproof surface.
•
Prior to each use, always check the device and accessories for
damage. Do not use damaged components.
• CAUTION!
Only process and heat up media that has a flash point
higher than the adjusted safe temperature limit of the heating
bath that has been set.
The safe temperature limit of the heating bath must always be
set to at least 25 °C lower than the fire point of the media used.
•
DANGER OF BEING BURNT!
When in operation the upper cor-
ner of the bath can heat up to 180 °C.
• Prior to filling or emptying the heating bath, the device must be
switched off and disconnected from the power supply at the
plug.
• Only fill or empty the heating bath when it is cold.
• Empty the heating bath prior to transporting it.
• Never operate the heating bath without tempering medium.
•
CAUTION!
The preferred tempering medium in the heating bath
is water (up to approx. 80 °C). Low viscosity silicone oils (50 mPas)
with a flashpoint > 260 °C are also permitted. There is a risk of bur-
ning when using tempering media with lower flashpoints!
• When using as a water bath, the use of demineralised water is
recommended.
• Always observe the minimum fill level of one litre when using oil
as the tempering medium.
Contents
Safety instructions
EN
EU
Declaration of conformity
3946600_HB10bdc_032009:3345300_VG3_042005_kvmb_1 28.04.2009 9:23 Uhr Seite 15
Содержание HB 10
