background image

ENGLISH

CAUTION

MAINTAIN GOOD VENTILATION

Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the cabinet bottom will
be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.

DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR

When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cables are disconnected. If you do not disconnect them, it may cause fire or electric shock.
It is recommended that two people are used when moving the monitor.

UNPLUG THE MONITOR

The power cable is the disconnect device. If the monitor is not in use for a long period of time it is
recommended that the power cable it is left unplugged to avoid accidents.

HOLD THE PLUG WHEN DISCONNECTING

To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable
itself as  this may cause fire or electric shock.

DO NOT TOUCH THE PLUG WITH WET HANDS

Pulling or inserting the plug with wet hands may cause electric shock.

DO NOT PUT FLOPPY DISKS NEAR THE MONITOR

Magnetic data recordings such as on a floppy disk may disappear if they are placed on or near the
monitor as the degauss circuit causes a strong momentary magnetic field.

WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER

Be  sure  the  computer  is  strong  enough  to  hold  the  weight  of  the  monitor,  otherwise,  you  may
damage your computer.

OTHERS

ERGONOMIC RECOMMENDATIONS

To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room.
For  optimal  viewing  comfort,  the  monitor  should  be  just  below  eye  level  and  40-60  cm  (16-24
inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break
every hour is recommended as looking at the screen continuously can cause eye strain.

MAGNETIC FIELD INFLUENCE

Place the monitor away from TV, speaker systems or any other source of strong magnetic fields.
The monitor may be noisy or the screen's output may be distorted as a result of interference from
other  appliances.

INTENDED APPLICATION

The monitor can be also used in a medical environment to display video signal from computer or
other system. The monitor is not suitable for use in areas that patients are cared for.

UNSUITABLE LOCATION FOR USING THE MONITOR

The monitor is not suitable for use in the presence of a FLAMMABLE ANAESTHETIC MIXTURE WITH
AIR or WITH OXYGEN OR NITROUS OXIDE.
The  monitor  is  not  suitable  for  use  in  areas  that  patients  are  cared  for.  This  encloses  a  space
within the room 1.83 m (6 feet) beyond the perimeter of the bed (examination table, dental chair,
treatment booth, and the like) in its intended location, and extending vertically 2.29 m (7-1/2 feet)
above  the  floor.

FOR YOUR SAFETY      2

Содержание HM204DT A
























Отзывы: