Iijima PACK LEADER RO-105LS Скачать руководство пользователя страница 36

Страница: 36 / 44

Symptom

Check

Action

Refer-

ence

page

The displayed CO

measurement value

is high.

Was a sample with a high concentration of CO

just

measured?

Measure the atmosphere once and then measure the same again. The

value can be high immediately after a high concentration sample was

measured.

calibration may not have been conducted properly.

Initialize the unit or conduct CO

calibration again with the CO

standard

gas on hand.

If the symptoms do not improve even after taking the above

actions, the CO

sensor may have reached its service life or

may be faulty.

The CO

sensor can be replaced only by Iijima Electronics Corporation.

Contact the dealer from which you purchased the product for

replacement and repairs.

The displayed O

measurement value

is zero.
Zero is displayed

even after the span

is calibrated.

Is the oxygen sensor correctly mounted?

Correctly mount the oxygen sensor onto the probe (blue).

Has water or foreign matter gotten between the oxygen

sensor and housing?

Remove the oxygen sensor and clean the inside of the housing. Lightly

wipe the metal mesh at the center of the oxygen sensor surface with

tissue paper, etc., to remove any moisture or foreign matter. Replace the

needle, membrane filter, check valve, and sampling tube with new parts.

Is the oxygen sensor wet, or have crystals formed on the

surface?

Replace the oxygen sensor with a new part.

(Contact the dealer from which you purchased the product if the

warranty is still valid.)

Is the probe cable damaged or disconnected?

Make a request for repairs.

If the symptoms do not improve even after taking the above

actions, the main unit may be faulty.

Make a request for repairs.

The displayed

measurement

value is zero.

Is the check valve mounted in the correct direction?

Re-mount in the correct direction so that the narrow side of the check

valve faces the sampling tube.

Is the connection of the needle, membrane filter, check

valve, or sampling tube loose?

Securely tighten the connection for the needle, membrane filter, check

valve, or sampling tube.

Is the needle, membrane filter, check valve, or sampling tube

clogged?

Check for clogging. If clogged, unclog the part or replace it with a new

part.
If the symptoms do not improve, make a request for repairs.

26,27

If the symptoms do not improve even after taking the above

actions, the CO

sensor may have reached its service life or

may be faulty.

The CO

sensor can be replaced only by Iijima Electronics Corporation.

Contact the dealer from which you purchased the product for

replacement and repairs.

The displayed O

and CO

measure-

ment value and

calibration value do

not change.

Is the check valve mounted in the correct direction?

Re-mount in the correct direction so that the narrow side of the check

valve faces the sampling tube.

Is the connection of the needle, membrane filter, check

valve, or sampling tube loose?

Securely tighten the connection for the needle, membrane filter, check

valve, or sampling tube.

Is the needle, membrane filter, check valve, or sampling tube

clogged?

Check for clogging. If clogged, unclog the part or replace it with a new

part.
If the symptoms do not improve, make a request for repairs.

26,27

Is the needle, membrane filter, check valve, or sampling tube

damaged?

Replace the damaged part with a new part.

(Only for O

) Is the oxygen sensor correctly mounted?

- - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - -

(Only for O

) Is the O-ring for the housing deviated?

Align‌the‌▲‌mark‌on‌the‌probe‌(blue)‌with‌the‌▲‌mark‌on‌the‌housing‌

(red).

- - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - -

Firmly mount the O-ring for the housing in the groove.

If the symptoms do not improve even after taking the above

actions, the main unit may be faulty.

Make a request for repairs.

Содержание PACK LEADER RO-105LS













































Результаты поиска

Содержание PACK LEADER RO-105LS

Отзывы:

Похожие инструкции для PACK LEADER RO-105LS

Бренды по названию

Популярные бренды

Iijima PACK LEADER RO-105LS, Руководство по эксплуатации

Результаты поиска

Содержание PACK LEADER RO-105LS

Отзывы:

Похожие инструкции для PACK LEADER RO-105LS

Бренды по названию

Популярные бренды