IFM SI5012 Скачать руководство пользователя страница 15

Страница: 15 / 17

Flow monitor

SI5012

10 Operation

After every power on all LEDs light and go out again step by step. During this time, the output is
closed if set to normally open and open if set to normally closed. Then the device is ready for
operation.

The device detects the flow and switches the output according to the setting.

The device displays the current flow and the switching status.

In case of power failure or interruption of the operating voltage, all settings remain.

Display

Explanation

LED 0 flashes

Current flow below the display range.

Current flow within the display range.

Current flow corresponds to the switch point.

Current flow above the switch point.

LED 9 flashes

Current flow above the display range.

Tab. 2: Display for normally open function, switch point at LED 4
LED orange: output closed; LED red: output open

Содержание SI5012


















Результаты поиска

Содержание SI5012

Отзывы:

Похожие инструкции для SI5012

Бренды по названию

Популярные бренды

IFM SI5012, Руководство по эксплуатации

Результаты поиска

Содержание SI5012

Отзывы:

Похожие инструкции для SI5012

Бренды по названию

Популярные бренды