IFM SAxx04 Series страница 3 Скачать руководство пользователя

Страница: 3 / 27

1 Preliminary note

Technical data, approvals, accessories and further information at

www�ifm�com�

►

Instructions

Reaction, result

[…] Designation of keys, buttons or indications

→

Cross-reference

Important note

Non-compliance may result in malfunction or interference�

Information

Supplementary note�

10�4 User settings (optional) ��22

10�4�1 Configure standard display ��22

10�4�2 Set the standard unit of measurement for flow ��22

10�4�3 Select the medium ��22

10�4�4 Define colour of the display ��23

10�4�5 Set the measured value damping ��23

10�4�6 Set output status in fault condition ��23

10�4�7 Calibrate curve of measured values ��23

10�5 Service functions ��24

10�5�1 Read min/max values ��24

10�5�2 Reset all parameters to factory setting ��24

11 Operation ��24

11�1 Read the process value ��24

11�2 Read the set parameters ��25

12  Technical data ��25
13  Fault correction ��25
14 Maintenance ��26
15  Factory setting ��27

Содержание SAxx04 Series




























Результаты поиска

Содержание SAxx04 Series

Отзывы:

Похожие инструкции для SAxx04 Series

Бренды по названию

Популярные бренды

IFM SAxx04 Series, Руководство по эксплуатации

Результаты поиска

Содержание SAxx04 Series

Отзывы:

Похожие инструкции для SAxx04 Series

Бренды по названию

Популярные бренды