IFM SAxx04 Series Скачать руководство пользователя страница 26

Страница: 26 / 27

Display Type

Description

Fault correction

S�Loc

Warning Setting buttons locked via

parameter software, parameter

change rejected�

►

Unlock the unit via IO-Link

interface using the parame-

ter setting software�

Warning Below the display range: tem-

perature value < - 20 % MEW

(→ 4.5)

�

►

Check temperature range�

►

Repeat low-flow adjustment�

Warning Display range exceeded: meas-

ured value > 120 % of MEW

(→ 4.5)

�

►

Check flow range / tempera-

ture range�

►

Repeat high-flow adjust-

ment�

SC1

Warning Switching status LED for OUT1

flashing: short circuit OUT1�

►

Check switching output

OUT1 for short-circuit or

excessive current�

SC2

Warning Switching status LED for OUT2

flashing: short circuit OUT2�

►

Check switching output

OUT2 for short-circuit or

excessive current�

Warning Switching status LEDs for

OUT1 and OUT2 flashing: short

circuit OUT1 and OUT2�

►

Check switching outputs

OU1 and OUT2 for short-cir-

cuit or excessive current�

FAIL

Warning Faulty low-flow or high-flow

adjustment (e�g� the distance

between maximum and mini-

mum flow is too small)�

►

Repeat flow adjustment�

MEW = final value of the measuring range

14 Maintenance

►

From time to time check the sensor tip for build-up�

►

Clean with soft cloth� Stubborn build-up, for example lime can be removed

using a common vinegar cleaning agent�

Содержание SAxx04 Series




























Результаты поиска

Содержание SAxx04 Series

Отзывы:

Похожие инструкции для SAxx04 Series

Бренды по названию

Популярные бренды

IFM SAxx04 Series, Руководство по эксплуатации

Результаты поиска

Содержание SAxx04 Series

Отзывы:

Похожие инструкции для SAxx04 Series

Бренды по названию

Популярные бренды