IFM PN78 Series Скачать руководство пользователя

Страница: 22 / 25

9.4 Service functions
9.4.1 Reading of the min/max values for system pressure

►

Select [HI] or [LO], briefly press [Set]�

[HI] = maximum value, [LO] = minimum value�

Delete memory:

►

Select [HI] or [LO]�

►

Press [Set] and keep it pressed until [----] is displayed�

►

Press [Mode/Enter] briefly�

9.4.2 Reset of all parameters to factory setting

►

Select [rES]�

►

Press [Set] and keep it pressed until [----] is displayed�

►

Press [Mode/Enter] briefly�

We recommend taking down your own settings in the table before carrying

out a reset (→ 13 Factory setting).

10 Operation

After power on, the unit is in the Run mode (= normal operating mode)� It carries

out its measurement and evaluation functions and provides output signals

according to the set parameters�

Operating indications → chapter 7 Operating and display elements.

10.1 Reading of the set parameters

►

Press [Mode/Enter] until the requested parameter is displayed�

►

Press [Set] briefly�

> The unit displays the corresponding parameter value for about 15 s� After

another 15 s the unit returns to the Run mode�

10.2 Fault indication

[OL]

Overload pressure (measuring range exceeded)

[UL]

Underload pressure (below measuring range)

[SC1]

Short circuit in OUT1*

[SC2]

Short circuit in OUT2*

[SC]

Short circuit in both outputs*

[Err]

Flashing: internal fault

*The output concerned is switched off as long as the short circuit exists�

The messages SC1, SC2, SC, and Err are shown even if the display is switched off�

Содержание PN78 Series


























Результаты поиска

Содержание PN78 Series

Отзывы:

Похожие инструкции для PN78 Series

Бренды по названию

Популярные бренды

IFM PN78 Series, Руководство по эксплуатации

Результаты поиска

Содержание PN78 Series

Отзывы:

Похожие инструкции для PN78 Series

Бренды по названию

Популярные бренды