background image

17

UK

9  Parameter setting

During parameter setting the unit remains in the operating mode� It continues its 

monitoring function with the existing parameters until the parameter setting has 

been completed�

9.1  General parameter setting

3 steps must be taken for each parameter setting:

1

Parameter selection

 

Press [Mode/Enter] until the 

requested parameter is displayed�

 

2

Setting of the parameter value

 

Press [Set] and keep it pressed�

 

> Current setting value of the 

parameter flashes for 5 s�

 

> After 5 s: setting value is changed: 

incrementally by pressing the button 

once or continuously by keeping the 

button pressed�

 

Numerical values are incremented continuously� To reduce the value: let the display 

move to the maximum setting value� Then the cycle starts again at the minimum 

setting value�

3

Acknowledgement of the parameter 

value

 

Press [Mode/Enter] briefly�

 

> The parameter is displayed again� 

The new setting value is stored�

 

Setting of other parameters:

 

Start again with step 1�

Finishing the parameter setting:

 

Press [Mode/Enter] several times until the current measured value is displayed or wait 

for 15 s�  

 

> The unit returns to the operating mode�

Содержание PN78 Series


























Отзывы: