IFM PN422 Series Скачать руководство пользователя страница 15

Страница: 15 / 17

9.3.3 Zero-point calibration

►

Select [COF] and set a value between -5% and 5% of the final value of

the measuring range� The internal measured value "0" is shifted by this

value�

Zero-point calibration reset:

►

Press [Mode/Enter] until [CAr] is displayed�

►

Press and hold [Set] until [---] is displayed�

►

Briefly press [Mode/Enter]�

9.3.4 Set delay time for OUT1

[dS1] = switch-on delay for OUT1�

[dr1] = switch-off delay for OUT1�

►

Select [dS1] or [dr1] and set a value between 0�1 and 50 s (at 0�0 the

delay time is not active)�

9.3.5 Setting the damping for OUT1

►

Select [dAP] and set a value between 0�01 and 4�00 s; (at 0�00 [dAP] is

not active)�

dAP value = response time between pressure change and change of the

switching status in seconds�

[dAP] influences the switching frequency: f

max

= 1 ÷ 2dAP�

9.4 Service functions
9.4.1 Read min/max values for the system pressure

►

Select [HI] or [LO], briefly press [Set]�

[HI] = maximum value, [LO] = minimum value�

Delete memory:

►

Select [HI] or [LO]�

►

Press and hold [Set] until [---] is displayed�

►

Briefly press [Mode/Enter]�

Содержание PN422 Series


















Результаты поиска

Содержание PN422 Series

Отзывы:

Бренды по названию

Популярные бренды

IFM PN422 Series, Руководство по эксплуатации

Результаты поиска

Содержание PN422 Series

Отзывы:

Бренды по названию

Популярные бренды