IFM LR7009 Скачать руководство пользователя

Страница: 6 / 36

LR7009

Electronic level sensor

3 Intended use

The device continuously monitors the level in tanks and generates output signals according to the
parameter settings.

2 switching outputs are available.

The outputs can be set separately.

In addition, the following is necessary for installation and operation:

•

One rod (for operation of the device with single probe)

Accessories.

•

Plus one coaxial pipe (for operation of the device with coaxial probe)

Accessories.

•

Mounting material (if necessary, a launching plate)

Accessories.

3.1 Accessories

Only use accessories from ifm electronic gmbh. The function is not ensured when using
components from other manufacturers.

The following components are available as accessories:

Rods

Length (cm)

Order number

E43225

E43203

E43226

E43204

E43227

E43205

100

E43207

120

E43208

140

E43209

160

E43210

Coaxial pipes with G¾ process connection

Length (cm)

Order number

E43211

E43228

E43212

E43229

E43213

100

E43214

120

E43215

140

E43216

160

E43217

Содержание LR7009





































Результаты поиска

Содержание LR7009

Отзывы:

Похожие инструкции для LR7009

Бренды по названию

Популярные бренды

IFM LR7009, Руководство по эксплуатации

Результаты поиска

Содержание LR7009

Отзывы:

Похожие инструкции для LR7009

Бренды по названию

Популярные бренды