IFM JN2301 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 25

IFM JN2301 Скачать руководство пользователя страница 21

UK

Inclination sensor JN

21

5-bit FMI -> 4
1-bit CM -> 0 (always 0)
7-bit OC -> 1

12 Status LED

The integrated LED indicates the current device state.

LED colour

Flashing frequency

Description

green (left connector)

permanently on

The device is in the "run" state

red (right socket)

permanently on

MEMS self-test failed

13 Maintenance, repair and disposal

The unit is maintenance-free.

► Dispose of the device in accordance with the national environmental

regulations.

14 Approvals/standards

The CE declarations of conformity and approvals can be found at www.ifm.com.

14.1 Reference to UL

The external supply source and external circuits intended to be connected to this
device shall be galv. separated from mains supply or hazardous live voltage by
reinforced or double insulation and meet the limits of clauses 6.3 Limit values for
accessible parts and 9.4 Limited energy circuit of UL 61010-1.
Minimum temperature rating and size of the cable to be connected to the field
wiring terminals, min. 75°C, min. 22 AWG or 0.34mm².

15 Factory setting

Index

Type

Value

Delivery

0x1100

u8

TxPGN1 active

1: is sent cyclically

0x2000

u8

Device address

25

0x2001

u16

Baud rate

250 Kbits

0x2040

u8

Flag for quadrant correction

1: corresponds to +/-180°

0x2041

u8

Flag for heating

1: corresponds to "heating on"

0x2042

u8

Index teach value of the X/Y/Z axes

2: corresponds to "absolute measurement"

0x2043

u8

FIR filter step

2: corresponds to "FIR lowpass 5Hz"

«
...
19
20
21
22
23
...
»

Содержание JN2301


























Отзывы:

Нет отзывов