IFM efector 160 LR3000 Скачать руководство пользователя страница 30

Страница: 30 / 38

Reset of all parameters to factory setting

10.6

Select [rES], then press [Set] and keep it pressed until [----] is displayed�

►

Press [Mode/Enter] briefly�

►

During the storage operation the display goes out for several seconds�

Then the unit restarts and the factory settings are restored�

Note: On delivery the unit is not operational� First, the basic settings must

be entered (→ 10.2).

Changing basic settings

10.7

Required after a factory reset [rES] and after changes to the probe or to the ap-

plication area�

New entering of the probe length

10.7.1

Approach for single probes:

Measure the rod length L to a precision of ± 2 mm (± 0�1 inch)� L = lower

►

edge of the of process connection to the rod end�

Round up the measured value (step increment 0�5 cm / 0�2 inch)�

►

Select [LEnG] and set the value (setting range: 10�0 �� 160�0 cm /(4�0 ��

►

63�0 inch)�

Approach for coaxial probes:

Measure the total length L

►

of the coaxial probe to a precision of ± 2 mm

(± 0�1 inch)�

Deduct 9 mm from the measured value� L = L

►

- 9 mm�

Round up the determined value (step increment 0�5 cm / 0�2 inch)�

►

Select [LEnG] and set the value (setting range: 10�0 �� 160�0 cm / 4�0 ��

►

63�0 inch)�

Note: After changing the probe length, the values for OFS and the switching

limits must also be reviewed / re-entered�

Setting to another medium

10.7.2

Select [MEdI] and set the value:

►

[HIGH] for water and water-based media�

[LOW] for oils and oil-based media�

Note: In case of doubt, carry out an application test to ensure the setting

which is best for your medium�

Содержание efector 160 LR3000







































Результаты поиска

Содержание efector 160 LR3000

Отзывы:

Бренды по названию

Популярные бренды

IFM efector 160 LR3000, Руководство по эксплуатации

Результаты поиска

Содержание efector 160 LR3000

Отзывы:

Бренды по названию

Популярные бренды