IFM Electronic SI5007 Скачать руководство пользователя страница 10

Страница: 10 / 17

7.1.2 Device-specific information

You will find the IODDs necessary for the configuration of the IO-Link unit and

detailed information about process data structure, diagnostic information and

parameter addresses at www�ifm�com/gb/io-link�

7.1.3 Parameter setting tools

You will find all necessary information about the required IO-Link hardware and

software at www�ifm�com/gb/io-link�

7.1.4 Adjustable parameters

SP1 / rP1 Upper / lower limit value for flow at which OUT1 switches
SP2 / rP2 Upper / lower limit value for flow at which OUT2 switches
OU1

Output configuration OUT1 (flow)

OU2

Output configuration OUT2 (temperature)

Set_High

Reading of the maximum flow (100 %)

Set_Low

Reading of the minimum flow (0 %)

dS1 / dr1

Switch-on delay / switch-off delay for OUT1

dS2 / dr2

Switch-on delay / switch-off delay for OUT2

Loc

Locks sensor operation to prevent unintentional maladjustment�

Can be reset on the unit�

7.2 Set-up and settings for water

For media other than water → 7.6 Low-flow adjustment (optional).

► Switch on the supply voltage�

> All LEDs light and go out again step by step� During this time output OUT1 is

closed (if configured as normally open)� The unit is in the operating mode�

► Let the normal flow circulate in the installation�

► Check the display and determine further actions�

The factory setting is suitable for the applica-

tion�

► For flow monitoring no further settings are

required�

Содержание SI5007


















Результаты поиска

Содержание SI5007

Отзывы:

Похожие инструкции для SI5007

Бренды по названию

Популярные бренды

IFM Electronic SI5007, Руководство по эксплуатации

Результаты поиска

Содержание SI5007

Отзывы:

Похожие инструкции для SI5007

Бренды по названию

Популярные бренды