IFM Electronic LR2059 Скачать руководство пользователя | Manualshive

Страница: 13 / 51

background image

13

UK

"smoothed" by means of a mean filter; the result is a steady curve. Damping

can

be set by means of the parameter [dAP]

.

[dAP] indicates in seconds after what time 63 % of the final value is reached in the

event of a sudden jump. After 5 x [dAP] almost 100 % has been reached.

6.3.5 Probes for different tank heights

The unit can be installed in tanks of different sizes. Probes in different lengths are

available. To adapt to the tank height, each probe can be shortened. The minimum

probe length is 150 mm, the maximum probe length 2000 mm.

6.3.6 Defined state in case of a fault

• In case of a fault a state can be defined for each output.
• If a fault is detected or if the signal quality is below a minimum value, the

outputs pass into a defined state, according to NAMUR recommendation in

case of the analogue output. For this case the response of the outputs can be

set via the parameters [FOU1], [FOU2]

• Temporary loss of signal caused e.g. by turbulence or foam build-up can be

suppressed by a delay time (parameter [dFo]

). During the delay

time the last measured value is frozen. If the measured signal is received again

in sufficient strength within the delay time, the unit continues to work in normal

operation. If, however, it is not received again in sufficient strength within the

delay time, the outputs pass into the defined state.

In case of heavy foam build-up and turbulence, note the examples of how

to create a steady area

«
...
11
12
13
14
15
...
»

Содержание LR2059




















































Отзывы:

Нет отзывов

Похожие инструкции для LR2059

Бренд: Kabuto Страницы: 25

Бренд: Banner Страницы: 10

Бренд: Dancover Страницы: 31

Бренд: Fantasea Страницы: 18

Бренд: Fantasea Страницы: 15

Бренд: Lastolite Страницы: 3

Бренд: Labona Страницы: 12

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 6

Portrait Series

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 10

Video 75 Plus Studio

Бренд: Sachtler Страницы: 34

Бренд: Allen Sports Страницы: 2

Fireplace Surrounds None

Бренд: Dimplex Страницы: 2

Бренд: Gira Страницы: 10

Бренд: BTC Страницы: 8

Бренд: U & Me Brothers Страницы: 6

Бренд: Urban Factory Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды