IFBlue IFBR1C, Инструкция по эксплуатации

Страница: 5 / 12

IFB Receiver
Rio Rancho, NM
5
Basic Operation
Frequency Selection
Press the FREQ button to select receiver frequency.
Frequency is shown in MHz. The
UP
and
DOWN
arrow
buttons adjust the frequency in 1 Mz steps. Press the
FREQ button again to select receiver frequency in KHz.
The UP and DOWN arrow buttons adjust the Frequency
in 25 KHz steps (VHF: 125 KHz steps).
NOTE: Holding down the
UP
or
DOWN
arrow
button, as opposed to a quick press, will scroll
through the frequency steps at an accelerated
pace.
Preset Selection
Press the
PRESET
button to select preset frequencies.
Presets are displayed as:
P on the left and the current preset number (1-10) on
the right
OR
If the current preset slot is empty, an E also appears
on the right. Use the
UP
and
DOWN
arrow buttons to
navigate among any programmed presets, tuning the
receiver to each.
The
UP
arrow makes the preset number increase while
the DOWN arrow makes it decrease.
NOTE: If the preset number is blinking, the
receiver IS NOT currently tuned to that preset.
Preset Programming
There are two options available for setting presets:
Choosing the preset slot first:
1. With the unit turned on, press the PRESET button
once, then press and hold the
PRESET
button until
the letter P blinks, indicating programming mode.
When navigating among the preset slots in this way,
all slots are accessible, even the empty ones, and
the receivers tuning is not affected.
2. Use the
UP
or
DOWN
buttons to navigate to the
desired preset slot.
3. If the desired preset slot is occupied, you can clear-
that slot by pressing and holding
DOWN
until you see the “E” appear and the preset number
is flashing, indicating that slot is now empty.
4. Press the
FREQ
button to display the frequency.
Press the FREQ button again and the MHz will be-
gin blinking. Use the
UP
or
DOWN
buttons to adjust
the frequency in MHz steps. Press the FREQ button
again and the kHz will begin blinking. Use the
UP
or
DOWN buttons to adjust the frequency in kHz steps.
5. Press the PRESET button to return to the presets
page. You should see the slot you chose, with the
“E” still there and the preset number blinking.
6. Press and hold UP to store the preset. The
E will disappear and and the preset number will
stop blinking, indicating that this slot has now been
programmed. The P will continue to blink indicat-
ing that you are still in programming mode, and
that your receiver is not yet tuned to this frequency.
Press PRESET once more to exit this mode and
the unit will now be tuned to this preset frequency.
The P will stop blinking.
Choosing the frequency first:
1. With the unit on, the frequency of operation should be
in the display. If not, press the
FREQ
button to dis-
play the currently tuned frequency. Press the FREQ
button again and the MHz will start blinking. Use
the UP or DOWN buttons to adjust the frequency in
MHz steps. Press the
FREQ
button again and the
kHz will begin blinking. Use the UP or DOWN but-
tons to adjust the frequency in kHz steps.
2. Press the
PRESET
button to display the preset page.
Press and hold PRESET again until the P starts
blinking, indicating programming mode. When
navigating among the preset slots in this way, all
slots are accessible, even the empty ones, and the
receivers tuning is not affected.
3. Use the UP or DOWN buttons to navigate to the
desired preset slot.
4. Press and hold
UP
to store the preset.
The E will disappear and the preset number will
stop blinking. The P will continue to blink indicat-
ing that you are still in programming mode, and
that your receiver is not yet tuned to this frequency.
Press PRESET once more to exit this mode and
the unit will now be tuned to this preset frequency.
The P will stop blinking.
Clear a Preset Selection
1. With the unit on, press PRESET to display the preset
menu. Press and hold
PRESET
until the letter P
blinks, indicating programming mode. When navi-
gating among the preset slots in this way, all slots
are accessible, even the empty ones, and the
receivers tuning is not affected.
2. Use the
UP
and
DOWN
buttons to navigate to the
preset slot you wish to clear.