IER i420
User Safety and Start Guide
Ce document est la propriété d'IER et ne doit pas être reproduit ou communiqué sans autorisation écrite
This document is the property of IER and may not be reproduced or communicated without prior written authorization.
Page 2
N0L8S2A6 P1
1. I420-220 PRODUCT TESTED AT 230 V, 50HZ, FOR EC MEASUREMENTS
This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause
radio interference.
COMPLIANCE STATEMENT FOR EUROPEAN USERS
CE marking shows conformity to the following criteria and provisions:
Low Voltage Directive (2014/35/EU)/EN60950-1
EMC Directive (2014/30/EU)/EN55032, EN55024, EN61000-3-2 & EN61000-3-3
This symbol on the equipment indicates the presence of an RFID module
The i420-220 version of the equipment may be fitted with radiating modules as indicated in the table here after:
Module
Manufacturer
Model
Frequency
Effective Radiated Power
RFID
Impinj
RS500-EU
865 to 868 MHz
+1.32 dBm
GS MARK STATEMENT
This product has been tested under EN ISO 7779 and has an acoustic level output no higher than 55db (A).
This device is not intended for use at a video workstation in compliance with Bildscharb V.
This device is not intended for use in the direct field of view at visual display workplaces. To avoid incommoding reflections at visual
display workplaces this device must not be placed in the direct field of view.
2. I420-120 PRODUCT TESTED AT 120 V, 60HZ, FOR FCC AND ICES MEASUREMENTS
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
This equipment complies with FCC’s radiation exposure limits set forth for an uncontrolled environment under the following conditions:
1. This equipment should be installed and operated such that a minimum separation distance of 20 cm is maintained between the
radiator (antenna) and user’s/nearby person’s body at all times.
2. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The i420-120 version of the equipment may be fitted with radiating modules as indicated in the table here after:
Module
Manufacturer
Model
Frequency
Effective radiated power
RFID
Impinj
RS500-GX
902 to 928 MHz
+23 dBm
EMI COMPLIANCE STATEMENT FOR CANADIAN USERS
This Class A digital apparatus complies with Canadian ICES-003.
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio and television reception. This digital apparatus does not exceed the
Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications. This equipment is designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Use shielded cables to connect this device to computers.
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the
equipment.
ETAT DE CONFORMITE E
MI A L’USAGE DES UTILISATEURS CANADIENS
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Cet équipement produit et utilise l’énergie à radiofréquences et s’il n'est pas installé et utilisé correctement, c’est à dire en accord
strict avec les instructions du fabricant, il risque de provoquer des interférences avec la réception de la radio et de la télévision.
Le présent appareil numérique n’émet pas de bruits radio électriques dépassant les limites applicables aux appareils numériques de
la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Cet équipement est conçu pour fournir une protection satisfaisante contre de telles interférences dans une installation résidentielle.
Cependant, il n’y a pas de garantie contre les interférences avec les réceptions radio ou télévision, provoquées par la mise en et hors
circuit de l’équipement; aussi, il est demandé à l’utilisateur d’essayer de corriger l’interférence par l’une ou plus des mesures
suivantes:
• Réorienter l’antenne de réception.
• Installer l’ordinateur autre part, par égard pour le récepteur.
• Brancher l’ordinateur dans une prise de courant différente de façon à ce que l’ordinateur et le récepteur soient branchés sur des
circuits différents.
PROVISOIRE
