IEMCA SIR52 MS52 F Скачать руководство пользователя страница 16

Страница: 16 / 212

2 - TECHNICAL INFORMATION

SIR 52 MS52 P/F

2 - Pag. 6 / 14

2.4 SAFETY

DEVICES

A INTERLOCKED MOBILE GUARD.It is associated to

microswitch (B):

- when selector

is turned to

, the bar

feeder stops by opening the guard;

- when selector

is turned to

, the

bar feeder does not stop by opening the
guard, but there are few controls enabled,
i.e. those necessary for setting up or change
the machining procedures; they are:

C AXIAL DISPLACEMENT LOCKING.

It is associated to sensor (D).

By releasing the lever, all lathe and bar feeder
functions are disabled.

E INTERLOCKED MOBILE GUARD.

Associated to microswitch (F).

By opening the guard, all lathe and bar feeder
functions are disabled.

G INTERLOCKED MOBILE GUARD.

Associated to microswitch (H).

By opening the guard, all bar magazine functions
are disabled. The bar feeder keeps feeding the
lathe until the feeding drum runs out of bars.

Содержание SIR52 MS52 F





















































































































































































































Результаты поиска

Содержание SIR52 MS52 F

Отзывы:

Похожие инструкции для SIR52 MS52 F

Бренды по названию

Популярные бренды

IEMCA SIR52 MS52 F, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание SIR52 MS52 F

Отзывы:

Похожие инструкции для SIR52 MS52 F

Бренды по названию

Популярные бренды