IEI Technology TANK-870AI SERIES Скачать руководство пользователя

Страница: 82 / 137

TANK-870AI Embedded System

Page 68



Disabled

EFAULT

Not perform ME unconfigure



Enabled

To perform ME unconfigure

5.3.6 F81866 Super IO Configuration

Use the

F81866

Super IO Configuration

menu (

BIOS Menu 8

) to set or change the

configurations for the serial ports.

Advanced

F81866 Super IO Configuration

F81866 Super IO Chip

F81866

> Serial Port 1 Configuration
> Serial Port 2 Configuration
> Serial Port 3 Configuration
> Serial Port 4 Configuration
> Serial Port 5 Configuration
> Serial Port 6 Configuration

Set Parameters of Serial
Port 1 (COMA)

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 8: F81866 Super IO Configuration

Содержание TANK-870AI SERIES










































































































































Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды

IEI Technology TANK-870AI SERIES, Руководство пользователя

Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды