IEI Technology PAC-400AI-C236 Скачать руководство пользователя страница 25

Страница: 25 / 110

PAC-400AI-C236 Embedded System

Page 15



Access can only be gained by SERVICE PERSONS or by USERS who have

been instructed about the reasons for the restrictions applied to the location
and about any precautions that shall be taken.



Access is through the use of a TOOL or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

3.2 Top Cover Removal

Before installing or maintaining the internal components, the top cover must be removed
from the PAC-400AI-C236. Follow the steps below to complete the task.

Step 1:

Remove all four top cover retention screws from the left side of the chassis.

Step 2:

Slide the cover leftwards and then lift the cover up gently.

Figure 3-1: Top Cover Removal

3.3 HDD Installation

The PAC-400AI-C236 allows installation of one 3.5" HDD/SSD. To install a HDD into the
system, please follow the steps below.

Step 1:

Remove the top cover from the PAC-400AI-C236. Please follow the instruction

described in

Section 3.2

Содержание PAC-400AI-C236















































































































Результаты поиска

Содержание PAC-400AI-C236

Отзывы:

Похожие инструкции для PAC-400AI-C236

Бренды по названию

Популярные бренды

IEI Technology PAC-400AI-C236, Руководство пользователя

Результаты поиска

Содержание PAC-400AI-C236

Отзывы:

Похожие инструкции для PAC-400AI-C236

Бренды по названию

Популярные бренды