IEI Technology NANO-ULT5 Скачать руководство пользователя страница 77

Страница: 77 / 147

NANO-ULT5 SBC

Page 63

4.7.4 Flash Descriptor Security Override Jumper

CN Label:

ME_FLASH1

CN Type:

2-pin header, p=1.27 mm

CN Location:

See

Figure 4-13

CN Settings:

See

Table 4-3

The Flash Descriptor Security Override jumper (ME_FLASH1) allows to enable or disable
the ME firmware update. Refer to

Figure 4-13

and

Table 4-3

for the jumper location and

settings.

Setting

Description

Open

Disabled (Default)

Short

Enabled

Table 4-3: Flash Descriptor Security Override Jumper Settings

Figure 4-13: Flash Descriptor Security Override Jumper Location

To update the ME firmware, please follow the steps below.

Step 1:

Before turning on the system power, short the Flash Descriptor Security

Override jumper.

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды