IEI Technology NANO-ULT5 Скачать руководство пользователя страница 126

Страница: 126 / 147

NANO-ULT5 SBC

Page 112

5.7 Exit

Use the

Exit

menu (

BIOS Menu 29

) to load default BIOS values, optimal failsafe values

and to save configuration changes.

Main

Advanced Chipset Security

Boot

Save & Exit

Save Changes and Reset

Discard Changes and Reset

Restore Defaults

Save as User Defaults

Restore User Defaults

Reset the system after

saving the changes.

---------------------



: Select Screen

↑

↓

: Select Item

Enter Select

F1 General Help

F2 Previous Values

Optimized

Defaults

Save

ESC Exit

BIOS Menu 29: Exit



Save Changes and Reset

Use the

Save Changes and Reset

option to save the changes made to the BIOS options

and to exit the BIOS configuration setup program.



Discard Changes and Reset

Use the

Discard Changes and Reset

option to exit the system without saving the

changes made to the BIOS configuration setup program.



Restore Defaults

Use the

Restore Defaults

option to load the optimal default values for each of the

parameters on the Setup menus.

F3 key can be used for this operation.

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды