IEI Technology ICE-BT-T10-E38151 Скачать руководство пользователя страница 89

Страница: 89 / 97

ICE-BT-T10 COM Express Module

Page 79

DIMM

Dual Inline Memory Modules are a type of RAM that offer a 64-bit data

bus and have separate electrical contacts on each side of the module.

DIO

The digital inputs and digital outputs are general control signals that

control the on/off circuit of external devices or TTL devices. Data can be

read or written to the selected address to enable the DIO functions.

EHCI

The Enhanced Host Controller Interface (EHCI) specification is a

EIDE

Enhanced IDE (EIDE) is a newer IDE interface standard that has data

transfer rates between 4.0 MBps and 16.6 MBps.

EIST

Enhanced Intel® SpeedStep Technology (EIST) allows users to modify

the power consumption levels and processor performance through

application software. The application software changes the bus-to-core

frequency ratio and the processor core voltage.

FSB

The Front Side Bus (FSB) is the bi-directional communication channel

between the processor and the Northbridge chipset.

GbE

Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0

Gbps and complies with the GPIO

General purpose input

HDD

Hard disk drive (HDD) is a type of magnetic, non-volatile computer

storage device that stores digitally encoded data.

ICH

The Input/Output Control Hub (ICH) is an Intel® Southbridge chipset.

IrDA

Infrared Data Association (IrDA) specify infrared data transmission

protocols used to enable electronic devices to wirelessly communicate

with each other.

L1 Cache

The Level 1 Cache (L1 Cache) is a small memory cache built into the

system processor.

L2 Cache

The Level 2 Cache (L2 Cache) is an external processor memory cache.

LCD

Liquid crystal display (LCD) is a flat, low-power display device that

consists of two polarizing plates with a liquid crystal panel in between.

Содержание ICE-BT-T10-E38151


































































































Результаты поиска

Содержание ICE-BT-T10-E38151

Отзывы:

Похожие инструкции для ICE-BT-T10-E38151

Бренды по названию

Популярные бренды

IEI Technology ICE-BT-T10-E38151, Руководство пользователя

Результаты поиска

Содержание ICE-BT-T10-E38151

Отзывы:

Похожие инструкции для ICE-BT-T10-E38151

Бренды по названию

Популярные бренды