IEI Technology ICE-BT-T10-E38151 Скачать руководство пользователя страница 56

Страница: 56 / 97

ICE-BT-T10 COM Express Module

Page 46

5.3.9 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 13

) to read USB configuration

information and configure the USB settings.

Advanced

USB Configuration

USB Devices:
1 Keyboard, 2 Hubs

Legacy USB Support

[Enabled]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.

---------------------



: Select Screen





: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 13: USB Configuration



USB Devices

The

USB Devices

field lists the USB devices that are enabled on the system



Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.



Enabled D

EFAULT

Legacy USB support enabled

Содержание ICE-BT-T10-E38151


































































































Результаты поиска

Содержание ICE-BT-T10-E38151

Отзывы:

Похожие инструкции для ICE-BT-T10-E38151

Бренды по названию

Популярные бренды

IEI Technology ICE-BT-T10-E38151, Руководство пользователя

Результаты поиска

Содержание ICE-BT-T10-E38151

Отзывы:

Похожие инструкции для ICE-BT-T10-E38151

Бренды по названию

Популярные бренды