IEI Technology HYPER-BT-E38 1 Series Скачать руководство пользователя страница 78

Страница: 78 / 95

HYPER-BT

Page 68



Primary IGFX Boot Display [VBIOS Default]

Use the

Primary IGFX Boot Display

option to select the display device used by the

system when it boots. For dual display support, select “VBIOS Deafult.” Configuration

options are listed below.



VBIOS Default

EFAULT



CRT



DP Port

5.4.2 Southbridge Configuration

Use the

Southbridge Configuration

menu (

BIOS Menu 17

) to configure the Southbridge

chipset.

Chipset

Auto Power Button Status

[Enabled(AT)]

Power Saving(EUP)

[Disabled]

Audio Configuration

Audio Controller

[Enabled]

EUP Disable/Enable.

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change  Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 17: Southbridge Chipset Configuration



Power Saving (EUP) [Disabled]

Use the

Power Saving (EUP)

option to enable or disable the power saving function.



Disabled

EFAULT

Power saving function is disabled.



Enabled

Power saving function is enabled. It will reduce power

consumption when the system is off.

Содержание HYPER-BT-E38 1 Series
































































































Результаты поиска

Содержание HYPER-BT-E38 1 Series

Отзывы:

Похожие инструкции для HYPER-BT-E38 1 Series

Бренды по названию

Популярные бренды

IEI Technology HYPER-BT-E38 1 Series, Руководство пользователя

Результаты поиска

Содержание HYPER-BT-E38 1 Series

Отзывы:

Похожие инструкции для HYPER-BT-E38 1 Series

Бренды по названию

Популярные бренды