manualshive.com logo in svg

IEI Technology AFL A-N270 Series, Руководство пользователя

Поделиться
Скачать
IEI Technology AFL A-N270 Series Скачать руководство пользователя страница 73

 

 

AFL-xxA-N270 Series Panel PC 

Page 59 

 

Only handle the edges of the PCB

: - When handling the PCB, hold the PCB 

by the edges. 

5.3 Turn off the Power 

 WARNING: 

Failing to turn off the system before opening it can cause permanent 

damage to the system and serious or fatal injury to the user. 

Before any maintenance procedures are carried out on the system, make sure the system 

is turned off. 

5.4 Opening the System 

5.4.1 Removing the Back Cover 

 WARNING: 

Over-tightening back cover screws will crack the plastic frame. 

Maximum torque for cover screws is 5 kg-cm (0.36 lb-ft/0.49 Nm). 

To access the AFL-xxA-N270 internally the back cover must be removed. To remove the 

back cover, please follow the steps below. 

Step 1: 

Follow all anti-static procedures

. See 

Section 5.2

. 

Step 2: 

Turn off the power

. See 

Section 5.3

. 

Step 3: 

Remove the retention screws on the back

. Remove the retention screws 

(

Figure 5-1

) from the back cover.   

Содержание AFL A-N270 Series











































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды