IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 72 / 170

AFL-xxA-N270 Series Panel PC

Page 58

5.1 System Maintenance Introduction

If the components of the AFOLUX AFL-xxA-N270 series fail they must be replaced.

Components that can be replaced include:

Module

Bluetooth

module

Wireless LAN module

SO-DIMM

module

Please contact the system reseller or vendor to purchase the replacement parts. Back

cover removal instructions for the AFOLUX AFL-xxA-N270 series are described below.

5.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the

AFL-xxA-N270 may result in permanent damage to the AFL-xxA-N270

and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the AFL-xxA-N270. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the AFL-xxA-N270 is accessed internally, or any other

electrical component is handled, the following anti-static precautions are strictly adhered

to.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

: - Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: - When configuring the AFL-xxA-N270, place it on an

antic-static pad. This reduces the possibility of ESD damaging the

AFL-xxA-N270.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды