IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 50 / 170

AFL-xxA-N270 Series Panel PC

Page 36

Description

Label

Type

Clear CMOS

J_COMS1

2-pin header

COM1 Pin 9 setting

JP8

10-pin header

COM3 Pin 9 setting

JP10

6-pin header

COM3 RX RS-232/422/485 select

JP9

8-pin header

COM3 TX RS-422/485 select

JP11

6-pin header

COM3 RS-232/422/485 select

JP6

12-pin header

Table 4-1: Jumpers

4.9.1 Access the Jumpers

To access the jumpers, remove the back cover. To remove the back cover, please refer to

Section 4.7

Step 1 ~ Step 4

4.9.2 Preconfigured Jumpers

WARNING:

Do not change the settings on the jumpers in described here. Doing so

may disable or damage the system.

The following jumpers are preconfigured for the AFL-xxA-N270. Users should no change

these jumpers (

Table 4-2

Jumper Name

Label

Type

LVDS voltage selection

J_VLVDS1

3-pin header

Touch Screen Select

4-pin header

Panel Type and Resolution

J_LCD_TYPE1

10-pin header

Table 4-2: Preconfigured Jumpers

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды