iDule ID2MB-CLIR Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 35

background image

1.

Product Outline

ID2MB-CLIR is a Camera Link (PoCL) interfaced and 2M resolution camera module.
2M pixels CMOS sensor with diagonal length 12.775mm is utilized. Entire pixels can be read out
within 1/140s at Medium Configuration output.

Features

□

Global Shutter CMOS sensor is utilized.

□

Camera Link (PoCL) Base , Medium, Full Configuration are supported.

□

Fixed trigger shutter mode, pulse width trigger shutter mode are operable.

□

Full frame rates are as follows.

2Tap Base Configuration

70fps

8bit/10bit

4Tap Medium Configuration*

140fps

8bit/10bit

8Tap Full Configuration

280fps

8bit

*Initial Setting

□

Center Trimming Output Mode

2Tap Base Configuration Center Trimming 1024(H)

151fps

8bit/10bit

Partial Scan 1024(V)

2Tap Base Configuration Center Trimming 512(H)

587fps

8bit

Partial Scan 512(V)

2.

Handling Precautions

The camera must not be used for any nuclear equipment or aerospace equipment with which mechanical

failure or malfunction could result in serious bodily injury or loss of human life. Our warranty does not apply to
dameges or defects caused by irregular and /or abnormal use of the product.

Please observe all warnings and cautions stated below.

Our warranty does not apply to damages or malfunctions caused by neglecting these precautions.

Do not use or store the camera in the following extreme conditions

:

- Extremely dusty or humid places.
- Extremely hot or cold places (operating temperature -5

℃

to +45

℃

).

                  - Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.
                  - Places subject to fluorescent light reflections.
                  - Places subject to unstable (flickering, etc.) lighting conditions.
                  - Places subject to strong vibration.

              · Remove dust or dirt on the surface of the lens with a blower.
              · Do not apply excessive force or static electricity that could damage the camera.
              · Do not shoot direct images that are extremely bright (e.g., light source, sun, etc.), and when camera is not
                  in use, put the lens cap on.

· Confirm the mutual ground potential carefully and then connect the camera to monitors or computers.

                  AC leaks from the connected devices may cause damages or destroy the camera.
              · Do not apply excessive voltage. (Use only the specified voltage.)    Unstable or improper power supply
                  voltage may cause damages or malfunction of the camera.
              · The voltage ripple of camera power DC +12V

±

10% shall be within

±

50mV. Improper power supply

                  voltage may cause noises on the video signals.
              · The rising time of camera power supply voltage shall be less than +10V, Max 60ms.    Please avoid
                  noises like chattering when rising.

«
1
2
3
4
5
...
»

Содержание ID2MB-CLIR




































Отзывы:

Нет отзывов

Похожие инструкции для ID2MB-CLIR

Бренд: Tamron Страницы: 4

Бренд: Hama Страницы: 9

Бренд: Kaya Instruments Страницы: 15

Бренд: Micca Страницы: 14

Бренд: Hama Страницы: 288

Бренд: XENO Страницы: 2

Бренд: Sandstrom Страницы: 16

Бренд: Teltonika Страницы: 4

Бренд: TZT Страницы: 12

Бренд: WolfVision Страницы: 20

TruVision Multi-Imager

Бренд: Interlogix Страницы: 22

Бренд: Lightrein Страницы: 20

Бренд: Yashica Страницы: 13

Бренд: Pentax Страницы: 48

Бренд: Curtis Страницы: 7

Бренд: iGuard Страницы: 2

Бренд: Hanwha Vision Страницы: 7

Бренд: Sinar Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды