background image

   
   
   
 

 

                 

13 

 

 

                                       

13. Warranty Policy and Limitation of Liability 

 

IDTECK warrants this product against defects in material and workmanship for 2 years from the date of 
purchase under normal customer use. This Warranty doesn’t apply: 1) to any product which has been 
dismantled without authorization of IDTECK or/and has a damaged or detached QC label on its back side; 
2) to any losses, defects, or damages caused by improper testing, operation, installation, maintenance, 
modification, alteration, or adjustment; 3) to any product with a damaged or faded serial number on it; or 
4) to any losses, defects, or damages caused by lightning or other electrical discharge, natural disaster, 
misuse, accident or neglect. 
 
This Limited Warranty is in lieu of all other warranties, obligations, or liabilities on the part of IDTECK, and 
IDTECK DISCLAIMS ANY AND ALL WARRANTY, WHETHER EXPRESS OR IMPLIED, OF 
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IDTECK does not, and cannot, 
know who is present, what property is located, where this product will be used; it would be extremely 
difficult to determine the actual damages that may result from a failure of the product to perform as 
anticipated; and the low price of this product is based upon the nature of the product provided and the 
limited liability that IDTECK assumes. IDTECK IS NOT RESPONSIBLE FOR ANY PERSONAL INJURY, 
PROPERTY DAMAGE OR LOSS, DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, 
OR OTHER LOSS, AND IDTECK’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE 
PURCHASE PRICE OF THE PRODUCT.   
 
To obtain repair or replacement under the terms of this warranty, visit IDTECK’s Website 
(http://www.idteck.com) and place an online RMA request.
 After an RMA code is issued, return the 
product along with the authorization RMA code. 
 

>> Warranty Period 

 

Product Category 

Warranty Period 

RF CARDS (ACTIVE TYPE) 

1 year 

FINGERPRINT MODULE / SENSOR 

RF READERS (WITHOUT EPOXY POTTING) 

2 years 

STANDALONE CONTROLLERS 

CONTROL PANELS 

FINGERPRINT READERS 

RF READERS (WITH EPOXY POTTING) 

Lifetime 

RF CARDS (PASSIVE TYPE) 

Содержание SR10S

















Отзывы: