IDTECK iPass IP100R Скачать руководство пользователя страница 60

Страница: 60 / 71

Troubleshooting

p.54

RF or PIN 15 + ENT

3. By modes, enter a user card, PIN and password.

Enter the master card (or PIN: 4 to 6digit (mode 03 or 05) + ENT).

See “Initial Setting” to register master or user.

If the problem still persists, contact our customer service center.

2.2

Problem

User card or PIN cannot be deleted.

Cause

●

An error in using a product or in system settings

●

System malfunction/data damaged or lost due to an external noise or a short circuit.

Solution

Make sure that installation and operation are normal.

☞ When the product operates normally

Having a master card or PIN

Having a user card that wish to delete

Enter the master card (or PIN: 4 to 6digit (mode 03 or 05) + ENT).

II.

Enter “mode 14 + ENT” to delete user access cards.

III.

Enter a user card to delete. If there have enough user cards that wish to delete, en

ter them in order continuously.

IV.

Enter the master card (or PIN: 4 to 6digit (mode 03 or 05) + ENT).

Loosing a user card that wish to delete (But knowing PIN of user card)

Enter the master card (or PIN: 4 to 6digit (mode 03 or 05) + ENT).

II.

Enter “mode 73 + ENT” to “Enable Keypad Input to Enter ID Number”.

III.

Enter the master card (or PIN: 4 to 6digit (mode 03 or 05) + ENT).

IV.

Enter “14 + ENT” to delete user access cards.

Enter “PIN + ENT”. If there have enough user cards that wish to delete, enter them

in order continuously.

VI.

Enter the master card (or PIN: 4 to 6digit (mode 03 or 05) + ENT).

Содержание iPass IP100R








































































Результаты поиска

Содержание iPass IP100R

Отзывы:

Похожие инструкции для iPass IP100R

Бренды по названию

Популярные бренды

IDTECK iPass IP100R, Руководство пользователя

Результаты поиска

Содержание iPass IP100R

Отзывы:

Похожие инструкции для iPass IP100R

Бренды по названию

Популярные бренды