IDTECK iMDC-MAIN Скачать руководство пользователя страница 23

Страница: 23 / 79

p.17

iMDC-RIM BOARD

Relay Output #

7 Port

Relay Output #

8 Port

TTL Input #1 P

ort

It’s the ports to accept TTL input.

TTL Input #2 P

ort

TTL Input #3 P

ort

TTL Input #4 P

ort

TTL Input #5 P

ort

TTL Input #6 P

ort

TTL Input #7 P

ort

TTL Input #8 P

ort

Power Port

It’s the port to accept power source.

iMDC uses DC +12V, Max.350mA current.

(When external devices such as door lock, alarm, sensor and reade

r are not connected.)

Mac Address S

ticker

It’s the sticker to indicate Mac address.

RJ45

It’s the Ethernet connection port to perform communication betw

een iMDC-MAIN and Host PC, iMDC-MAIN and the other iMDC-M

AINs, iMDC-MAIN and iMDC-RIM.

Power Status L

Connector

It’s the connector to be connected to enclosure using cable. If red

LED is turned on, it means power has properly supplied.

Communicatio

n Status

LED Connector

It’s the connector to be connected to enclosure using cable. Green

LED indicates status of Ethernet communication.

Communicatio

n Status

LED Connector

It’s the connector to be connected to enclosure using cable. If com

munication between iMDC-MAIN and iMDC-RIM starts, the yellow

LED turns on.

Reset Switch

It’s the reset switch to reboot the device. The set information main

No.

Code

Description

Содержание iMDC-MAIN
















































































Результаты поиска

Содержание iMDC-MAIN

Отзывы:

IDTECK iMDC-MAIN, Руководство пользователя, Страница: 23 / 79

Результаты поиска

Содержание iMDC-MAIN

Отзывы: