background image

 

General specifications 

General specifications :

 

Frequency response : +0 / - 0.4dB, 10-20000Hz (Bypass 

mode). 

System distortion : < 0.01% THD, de-emphasised. 

Signal to Noise : 92 dB unweighted, 20 Hz - 20 kHz 

I/O Delay : ~13 milliseconds for the DVP and ~ 6 

milliseconds for the DBP 

Internal sample rate : 96 kHz 

Internal resolution : 40 bit floating point 

I/O resolution : 24 bit 

Maximum Overshoot : 0.1 dB 

Phase Response : Linear 20 Hz - 20 kHz 

Process Architecture DVP: FFT (Fast Fourier Transform) 

Process Architecture DBP: Band process 

Process structure : 1APP (One Advanced Point 

Processing) 

DSP : 10 Sharc 21065, expandable to 66 DSP. 

Maximum number of Factory Presets : 32 

Maximum number of User Presets : 64 

Remote contact closure : 14 Presets 

 

Analogue Audio Input :

 

Configuration : Stereo 

Impedance : > 6 kOhms 

Type : Electronically balanced 

Maximum Input Level : +25 dBu, for THD + N < 0.01% 

Equivalent Input Noise : < - 84 dBu 

Common Mode Rejection Ratio: 90 dB 

Connector : two XLR female 

A/D Conversion : 24 bit 128X oversampled 

 

Analogue Audio Output :

 

Configuration : Stereo 

Source impedance : < 1 Ohms 

Type : Electronically balanced 

Maximum Output Level :   

+24 dBu, on 10 kOhms Load for THD + N < 0.01 % 

+18 dBu on 600 Ohms Load for THD + N < 0.05 % 

Signal to Noise : > 100 dB unweighted, 20 Hz - 20 kHz 

Connector : Two XLR male 

DA Conversion : 24 bit 128X oversampled 

 

Digital Audio Input :

 

Configuration : Stereo per AES/EBU (AES3), 16, 18, 20 or 

24 bit resolution.  

Impedance : 110 ohms 

Sample Rate : 32, 44.1, 48, 96kHz autodetect 

Status bits : Input channel status is decoded for control. 

Input user bits are optionally passed trough the output. 

Connector : XLR female, EMI-suppressed 

Filtering : RFI filters. BW : 0.5-200MHz 

 

Digital Audio Output :

 

Configuration : Stereo per AES/EBU (AES3), 20 or 24 bits 

resolution. 

Impedance : 110 ohms 

Sampling Rate : Software selectable, free running at 

32kHz +/- 10 PPM, 44.1kHz +/- 10 PPM, 48kHz +/- 10 

PPM, 96kHz +/- 10 PPM. 

Synchronisation mode : Internal free running or external 

or delivery mode for 32, 44.1, 48, 96 kHz 

Word Length : Selectable 18, 20, 24 bits. 

Jitter : Less than 5 ns rms. 

Status bits : Output channel status can be generated. 

Input User bits are optionally passed through the output 

Connector : XLR male, EMI-suppressed 

Filtering : RFI filtered. BP : 0.5-200MHz

 

 

 

 

IDT Sound Processing Corporation reserves the right to make changes without previous notification. Illustrations, 
descriptions and characteristics are not contractually binding and not engage the responsibility of the manufacturer. 

Digital Sync Input / Output :

 

Configuration : Two mode, input to provide sync, Output 
to deliver sync 
Impedance : 75 ohms 
Sampling Rate for Input mode : 32, 44.1, 48, 96 kHz 

Sampling Rate for Output mode :  Software selectable, 
32 kHz +/- 10 PPM, 44.1 kHz +/- 10 PPM, 48 kHz +/- 10 
PPM, 96 kHz +/- 10 PPM. 
Connector : BNC female. 
 

Digital Stereo Generator :

 

Frequency Response : +/- 0.1 dB 20Hz - 15 kHz 
Configuration : Two independently controlled output 

Source impedance : 75 ohms 
Load impedance : 75 ohms or grater 
Level : Adjustable max 15 Vpp (100% modulation ~ -3 
dBfs) 
Connector : BNC 
Pre-emphasis : 50 or 75

μ

Stereo separation : More than 90dB, 20Hz - 15 kHz 
Main to Sub crosstalk, Sub to Main crosstalk : < -85 dB 
Audio filtering : 80 dB rejection at 19kHz 
Pilot stability : +/- 0,2 Hz 
Pilot Output 19 kHz : 1 BNC 

Sub-carrier : Two BNC input  
 

Remote Computer Interface :

 

Configuration : Two RS 232 
Connector : One Sub-D 9 pin female and one Sub-D 9 pin 
male 
Baud rate : Auto selectable baud rate 9600 to 115200 
bauds 

 

Remote Control :

 

Configuration : Fully remote controllable by external 

modem or TCP/IP (optional). 
Rate : 9600 to 115200 bauds 
 

Remote Control Interface :

 

Configuration : 14 inputs contact closure 
Control : 14 users presets directly selectable by software 
 

Power :

 

Voltage : 80 to 265 VAC, 50 - 60 Hz, 130 VA 
Connector : IEC, EMI-suppressed 
Safety Standard : CE / DBT 

 

Environmental and Dimensions :

 

Operating Temperature : 0° à 50° C or 32° to 122° F 

Humidity : 0 to 95% RH, no condensing 
Size : 19'', Two rack unit high. (W x H x D) : 48,3 x 8.9 x 
40 cm  - 19 x 3.5 x  15.7''  
Weight : 6 Kg - 13.2 lb. 

 

 

93

 

IDT – SOUND PROCESSING CORPORATION – TECHNOPARC – 5 Allée Moulin Berger – 69130 ECULLY – France 

Tel +33/(0) 472.18.19.20 - Fax +33/(0) 472.18.19.21 - Web  www.idt-fr.com – e-mail : [email protected]

 

Содержание DBP 7+4






























































































Отзывы: