manualshive.com logo in svg

IDT 89HPES34H16, Руководство пользователя, Страница: 133 / 182

Поделиться
Скачать
IDT 89HPES34H16 Скачать руководство пользователя страница 133

IDT   Configuration Registers

PES34H16 User Manual

9 - 41

October 30, 2008

Notes

AERUEM - AER Uncorrectable Error Mask (0x108)

Bit 

Field

Field

Name

Type

Default

Value

Description

0

UDEF

RW

0x0

Sticky

Undefined. This bit is no longer used in this version of the 
specificiation.

3:1

Reserved

RO

0x0

Reserved field.

4

DLPERR

RW

0x0

Sticky

Data Link Protocol Error Mask. When this bit is set, the cor-
responding bit in the AERUES register is masked. When a bit 
is masked in the AERUES register, the corresponding event 
is not logged in the advanced capability structure and an error 
is not reported to the root complex.

5

SDOENERR

RW

0x0

Sticky

Surprise Down Error Mask. When this bit is set, the corre-
sponding bit in the AERUES register is masked. When a bit is 
masked in the AERUES register, the corresponding event is 
not logged in the advanced capability structure and an error is 
not reported to the root complex.

11:6

Reserved

RO

0x0

Reserved field.

12

POISONED

RW

0x0

Sticky

Poisoned TLP Mask. When this bit is set, the corresponding 
bit in the AERUES register is masked. When a bit is masked 
in the AERUES register, the corresponding event is not 
logged in the advanced capability structure and an error is not 
reported to the root complex.

13

FCPERR

RW

0x0

Sticky

Flow Control Protocol Error Mask. When this bit is set, the 
corresponding bit in the AERUES register is masked. When a 
bit is masked in the AERUES register, the corresponding 
event is not logged in the advanced capability structure and 
an error is not reported to the root complex.

14

COMPTO

RO

0x0

Completion Time-out Mask. A switch port does not initiate 
non-posted requests on its own behalf. Therefore, this field is 
hardwired to zero.

15

CABORT

RO

0x0

Completer Abort Mask. The PES34H16 never responds to a 
non-posted request with a completer abort.

16

UECOMP

RW

0x0

Sticky

Unexpected Completion Mask. When this bit is set, the cor-
responding bit in the AERUES register is masked. When a bit 
is masked in the AERUES register, the corresponding event 
is not logged in the advanced capability structure and an error 
is not reported to the root complex.

17

RCVOVR

RW

0x0

Sticky

Receiver Overflow Mask. When this bit is set, the corre-
sponding bit in the AERUES register is masked. When a bit is 
masked in the AERUES register, the corresponding event is 
not logged in the advanced capability structure and an error is 
not reported to the root complex.

18

MAL-

FORMED

RW

0x0

Sticky

Malformed TLP Mask. When this bit is set, the correspond-
ing bit in the AERUES register is masked. When a bit is 
masked in the AERUES register, the corresponding event is 
not logged in the advanced capability structure and an error is 
not reported to the root complex.

Содержание 89HPES34H16























































































































































































Отзывы:

Нет отзывов